These blowguns have a metal body.

Designed to reduce noise, these blowguns are quieter than similar standard guns.

Compact enough to carry with you, these guns have a built-in quick-disconnect hose coupling for easy connection to an air line.

Connect the included hose to your air supply and these blowguns are ready to use.

Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.

The included hose is ready to connect to your air supply.

These guns include a rubber tip that won't damage your workpiece.

Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris.

These blowguns provide more than two times the airflow of standard guns.

The extra length lets you access hard-to-reach areas.

Air flows out of the side of the nozzle to clean air filters, radiators, and inside recesses.

Clear dust and debris, test air ducts for leaks, and dry large surfaces without needing a compressed air line.

Blow off dust and contamination, eliminate static charges, and guard against ESD (electrostatic discharge).

A nonconductive plastic nozzle and tip protect against accidental contact with live electrical circuits. These blowguns are tested to 1,000 volts to meet IEC 60900.

Also known as siphon guns, these spray air and liquids at the same time. Push the lever and the airflow creates suction that draws water, cleaning solution, or other liquids through the hose.

Prevent buildup of electrostatic discharge (ESD) that can damage electronic components.

Precisely control heat with a tool that senses the temperature of your work surface. Set the desired surface temperature and the gun will maintain it, regardless of variations in distance.

Choose these guns for occasional heating.

Concentrate a heat gun's airflow.

Shaped to hold round objects, use these nozzles for installing heat-shrink tubing and bending plastic pipe.

Save up to four temperature and airflow settings.

Distribute heat over a wide area for large jobs.

Blast your heating, drying, and shrinking projects with hot air to get the job done quickly. Choose from blowers with temperature settings from 300° to 750° F.

Combine high-volume airflow with low-heat output for warming and drying.

Use these guns to clean as well as apply chemicals and solvents.

Slide the metal sleeve up to the tip for rigidity. Slide it back down to expose the flexible nozzle.

Sets include dispensing tips for grease fittings and bare lubrication points.

These flexible nozzles have threads on both ends for connecting a grease gun to a dispensing tip.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Dispense from grease guns into grease fittings and bare lubrication points.

With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.

Lubricate standard grease fittings in hard-to-reach areas. Extensions have a quick-disconnect fitting that snaps into your dispensing tip for standard grease fittings.

Drive bigger staples than you can with standard air-powered staplers.

These staplers have a smaller body and are 50% lighter than our other air-powered staplers.

Let compressed air do the work for you when dispensing sealants from cartridges.

An extra-long nosepiece allows access to hard-to-reach areas.

Use these tools for repair and maintenance work.

Compressed air creates a vacuum that securely holds the rivet in the tool before installation and ejects the mandrel out of the tool after.

These vortex tubes are UL listed for Class I, Division II, Groups A, B, C, and D hazardous locations.

Set the thermostat and these vortex tubes switch on only when needed.

Kits include one vortex tube for converting compressed air into a stream of cold air as well as airflow adjusters, a cold-air muffler, a tube fitting, and tubing.

Often used in low-noise environments such as labs and clean rooms, these are quieter than standard enclosure-cooling vortex tubes.

Built for durability, these high-performance tools handle the demands of high-volume production and tough maintenance applications.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.