Install these pins in a plate or table and mate with holes in a workpiece for precise alignment.

Screw the shank into a threaded hole for quick installation and removal.

Encase these pins while molding plastic or composite parts. Once set, the knurls resist movement, letting you align the workpiece with precision on a plate or table.

When locating a workpiece using through-hole alignment pins, use one of these bushings and one standard bushing to prevent the pins from binding in your fixture.

Use the handle on these retractors to extend and retract a locating pin, protecting the pin from damage in applications where fixtures move through a process, such as along a conveyor belt.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Support rounded or irregularly shaped workpieces from the bottom or side with minimal contact.

Set the tang in a slot below the work surface to prevent thin material from sliding underneath the face.

Sealed at the top to prevent debris from getting inside and making them seize up, these guide pins are a good choice for machining fixtures.

Threading makes these guide pins easier to remove and replace than press fit, so they're useful for high-wear applications.

Use these pins for visibility or to color-code processes. For a more secure hold than standard quick-release pins, they lock in place until you push the button to release the spring-loaded retaining balls.

When there isn't enough room for a T-handle, an L-handle saves space but is still easy to grip. For a more secure hold than standard quick-release pins, these pins lock in place until you push the button to release the spring-loaded retaining balls.

Four spring-loaded retaining balls provide extra holding power. Made entirely of stainless steel, these pins stand up to corrosive enviroments. They lock in place until you push the button to release the spring-loaded retaining balls.

A recessed button prevents accidental pin removal. These all-stainless steel pins stand up to corrosive environments. They lock in place until you push the button to release the spring-loaded retaining balls.

Attach these pins to a machine cover or access panel, then clip them in to receptacles installed in the enclosure for quick access. Pins lock in place until you release them.

Also known as double-acting pins, these pins lock in place until you push or pull the handle to release the spring-loaded retaining balls. The T-handle is easy to grip.

To insert and remove these pins, press the button, then flip the lever to release the spring-loaded retaining balls. Two-step locking prevents accidental removal.

A bright-orange plastic-coated handle makes these pins easy to see and easy to grip. Pins have a spring-loaded ball that pops out when the pin is pushed into a hole, and retracts when the pin is pulled out.

Add a knob or handle to the threaded shank. A spring-loaded, nonlocking retaining ball pops out when the pin is pushed through a hole, and retracts when the pin is pulled out.

A smooth ball handle is easy to grip and won't catch on other parts. A spring-loaded, nonlocking retaining ball pops out when the pin is pushed through a hole, and retracts when the pin is pulled out.

The smooth ring handle on these pins won't catch on parts. The shoulder keeps a portion of the pin outside the hole and makes them easy to grab.

These pins combine the locking capabilities of a clevis pin with the precision diameter of a dowel pin for a tight fit.

A plastic-coated T-handle welded to these pins makes them easy to grab.

Install or remove these pins from either side.

These pins have multiple through holes; change the length by moving the cotter pin. The bend makes them easy to insert and pull out.

A swivel handle makes these pins easy to install and remove, while the toggle locks them in place. Flip the toggle to release the pin.

A swivel handle makes these pins easy to install and remove, while the toggle locks them in place. Flip the toggle to release the pin.

Slide a retaining ring into the groove for a secure hold that takes up less space than a cotter pin.

Sized to fit snugly around pipe and tube, these pins use spring force to keep the retainer closed.

Use a padlock to secure these pins. The bend makes them easy to insert and pull out.

Plastic pins are a nonconductive and nonmagnetic alternative to metal dowel pins. Use them as pivots, hinges, shafts, jigs, and fixtures to locate or hold parts.

Oversized to fit worn and enlarged holes, these pins work well as repair and replacement parts.

To remove these pins, thread a screw or tool into the tapped hole, then pull them out.

A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

These pins are commonly used as anchors for tension springs. The grooved half locks pins in position, and spring ends fit in to the notch. Also known as type G pins.

Center-groove pins are often used in place of clevis pins or to create T-handles. The grooved center locks pins in position, while the smooth ends act as a pivot. Also known as type E pins.

Grooves run the full length of these pins for a firm hold that won't spin. Use them in place of standard dowel, spring, and taper pins to fasten parts. Also known as type A pins.

Use these as pivot or hinge pins. The knurled half locks pins in position, while the smooth half acts as a pivot.

Join two pieces of wood with these dowel pins. When glued, they expand for a tight fit.

Pass wires and other components through these hollow pins.

A 60° beveled head fits into a countersunk hole.

A thick shoulder makes these pins more rigid than standard ejector pins.

Threads on these pins stick out for easy removal from blind holes. Tighten the hex nut to draw the pin out.

Weld these pins directly to a surface —no mounting hole required.

Quickly align, join, or hold machine components in place in food, pharmaceutical, and other sanitary environments. Pulling the plunger knob and twisting it 90° will lock the nose into its retracted position.

The ring allows you to attach these spring plungers to a lanyard.

Use the lanyard as a tether to secure the spring plunger to machinery and prevent accidental drops.

Lock the nose into the retracted position by pulling the knob and rotating it 90°.

Insert the nose into a panel; then thread on the nut and tighten using an installation wrench.

A quarter turn of the handle locks these plungers in the retracted position. The T-handle is easy to grip.

A smooth ball handle is easy to grip and won't catch on other parts.

An L-handle takes up less space than a T-handle.