Line up holes by driving these pins through existing rivet, pin, and bolt holes in multiple pieces of metal. Alternatively known as lineup taper punches.

Made from aluminum-bronze that is Factory Mutual approved, these nonmagnetic, corrosion-resistant tools inhibit sparking. They satisfy OSHA requirements for nonsparking tools.

These brass tools reduce marring on metal surfaces because they're softer than steel punches.

These brass tools reduce marring on metal surfaces because they're softer than steel punches.

Check for proper alignment of pulley systems with these magnetic-mount lasers. Place them on pulleys, gears, or sprockets made of ferrous metals, such as steel.

Fine-tune the size of the laser dot.

Projecting a light that's even and bright the entire length, these lasers create a line that can be measured from end to end.

With a sealed lens and an IP67 rating, these lasers are dust and liquid tight, so you can mount them to machines in dusty or wet areas such as labs, warehouses, or marine environments to align components.

These kits include a laser, a beam splitter, and a leveling plate.

Mark a dot up to 500 feet across your plant.

These levels project three dots simultaneously to verify your installation is straight, level, and plumb.

Whether you’re hanging a drop ceiling or aligning bench tops, use the cross-hair lines of these lasers to install material at the right height.

The sturdy box-style housing has precision-machined leveling surfaces to ensure accuracy.

Lightweight yet strong and durable, these bamboo levels won't stick to wet cement. Also known as masonry levels.

These levels come with a calibration certificate that's traceable to NIST and includes the test measurements that confirm accuracy.

A color LCD and highly accurate sensor allow you to level both horizontally and vertically at the same time.

A color LCD and highly accurate sensor allow you to level both horizontally and vertically at the same time. This level also displays a real-time vibration graph.

These levels have a sturdy aluminum housing.

Slip these levels into a drilled hole.

Plastic vials are more durable than glass.

Maintain consistent alignment in mating parts by installing a pin in one part and a liner in the other.

Install these pins in a plate or table and mate with holes in a workpiece for precise alignment.

Screw the shank into a threaded hole for quick installation and removal.

Use the handle on these retractors to extend and retract a locating pin, protecting the pin from damage in applications where fixtures move through a process, such as along a conveyor belt.

Precisely align drilled holes in two parts.

Instead of keeping an assortment of parallels on hand, adjust these two-piece tools to your exact height requirements.

Sets include multiple sizes of matched pairs that are precision ground for tight tolerances on the top and bottom edges.

Slide these low-profile supports under a workpiece to provide support and reduce vibration.

Adjust the horizontal screw to hold workpieces of varying sizes in precise positions.

Use this block to hold workpieces at precise angles.

Use these pairs of blocks to support long, round workpieces—secure with the built-in clamps.

To hold and support large or small round or cylindrical workpieces, position these two-piece V-blocks to accommodate any diameter.

A bright yellow vise body stands out on the shop floor.

For big jobs, these vises have a wider jaw opening, deeper throat depth, and larger footprint than standard vises.

Rotate the head 360° to use three different vise jaws and lock workpieces in position at 45° intervals.

Use these vises for general purpose workholding.

Replace worn flat and V jaws.

For large workpieces, these vises open three times as wide as standard tilting-head vises. Tilt and lock the head to position work at an angle.

Place over the jaws and tighten the screws to securely attach liners.

Choose from flat and grooved liners.

These V-shaped liners hold large round material.

Hold your smallest workpieces in these vises, which have a clamp-on base for quick installation and removal from a benchtop.

The vise body and stationary jaw are one piece for high repeatability, even under heavy clamping loads. Ground flat on the base and three sides, these vises ensure accuracy whether mounted on the base, either side, or upright.

Store vise handles near your milling machine.

Made from unhardened aluminum or steel, machine these jaws to fit the contours and curves of your workpiece.

Hold workpieces steady with these vise jaws—they work with slot-mount workstops so you can quickly position, adjust, and change out your workpieces.

Mount to a machine table to rotate a vise 360° in 1° increments.

Hardened for wear resistance, these steel jaws are replacements for the ones that come installed on your vise.

Maintain your vise by replacing seals, springs, and other commonly worn parts.

The small size allows multiple vises to be mounted on a single machine table. Frequently used in 4- and 5-axis milling machines, these vises have stepped jaws with serrated teeth that firmly grip just a small portion of your workpiece.

Tilt the head on two axes and rotate the base to position your workpiece at almost any angle.

Reliably hold workpieces with these basic machine vises.

The entire surface of these plates is magnetic to provide a powerful hold for grinding, drilling, and electrical discharge machining (EDM). Pull the handle to switch the magnets on and off.

Mount these workstops into slotted vise jaws—they hold workpieces in place and prevent horizontal movement during machining.

Use the adjustment dials to ensure your work is accurately positioned on X and Y axes.

The dials on these vises are graduated in smaller increments than standard cross-slide drill-press vises for finer adjustment. Use to precisely position work on X and Y axes.

Turn the handle to move the jaw on these basic vises.

Steel jaws secure round workpieces such as pipe, tubing, and conduit.

Keep clean rooms free of contaminants. These tripod-mounted vises have rubber-covered jaws that prevent metal-to-metal contact and a plastic-encased chain that seals in lubrication.

Sets include four vises with different opening sizes. A hollow body allows wires and rods to pass through.

Clamp and unclamp with one hand by sliding the knurled ring forward to close the collet.

Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the vise with your fingertips.

Notches on the jaws hold round material on its outside diameter.

Squeeze the body to open the flat jaws; release to grip.

Arrange the pins in a series of holes to grip parts with angled or uneven sides.