The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

A scaled-down version of standard screwdrivers, these tools are shorter, slimmer, and easy to take with you.

The ball-end tip allows angled entry to turn screws in hard-to-reach areas. These tools are a scaled-down version of standard changeable-shaft screwdrivers, They're shorter, slimmer, and easy to take with you. Remove and replace the shaft to change the tip size.

A retaining ring grips inside the recess to hold screws in place. These bits have a ball end that allows angled entry to drive screws in hard-to-reach areas.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

Assortments contain bits with multiple drive styles.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

Also known as Bristol bits, these have a knurled-end shank that allows finger tightening. They can also be used with the included screwdriver.

The slightly tapered tip wedges into the screw recess for a secure hold. These are also known as Torx-Align bits.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Designed for the fasteners used in electronics assembly, the tip of these bits has slightly sharper corners than Phillips style.

Use with screws that have two drilled holes.

Grip the indentations on the head of tri-groove fasteners.

Sets include an assortment of drivers with a rotating end cap on the handle that allows you to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Sets include an assortment of drivers with a tip that can be replaced when it becomes worn. Press the rotating end cap on the handle with your palm to apply constant pressure to small fasteners while turning the body of the screwdriver with your fingertips.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

These sets include an assortment of keys with a ball end on the long shaft, which allows angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

These assorted keys have a ball-end tip with a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

The short bit on these sockets fits in spaces where height clearance is limited.

Pivot the head of the sockets in these sets to access fasteners from an angle.

Tighten or loosen hard-to-reach fasteners with the extra-long bits in these socket sets.

Keep a convenient variety of drive styles and sizes of bit sockets on hand.

Attach one of the heads in these sets to a torque wrench for more leverage to loosen a stubborn fastener.

Get a strong grip in tight areas, even on fasteners that are rounded or damaged.

Suitable for occasional maintenance work, these sets are imported.

Access 6-point nuts and bolts in tight and awkward spaces—the heads on these sockets pivot.

Two spring-loaded balls inside these sockets firmly hold nuts and bolts in place as you turn them, including nonmagnetic fasteners like stainless steel screws.

Made of aluminum-bronze, these sockets satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Turn 90° elbow fittings that are in tight spots with the sockets in these sets.

Pivot the head to access fasteners from an angle.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

Pivot the head to access fasteners from an angle.

The hex shape grips hex fasteners and prevents rounding. These sockets are made to withstand the high torque and force of impact tools.

Carry fewer impact sockets—these five reversible impact sockets turn 10 fastener sizes. Flip the socket around to turn a different size.

Use one socket to switch between two fastener sizes.

Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.

The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.

Made of stainless steel, these wrenches have excellent corrosion resistance.

The slim heads fit into tight spaces and around thin fasteners.

The heads are offset to provide clearance for reaching over obstructions.

Open the jaws to fit around a fastener like an open-end wrench; close the jaws and the wrench acts like a ratcheting box wrench.