Insulated to protect against accidental contact with live electrical circuits, these sockets are tested to 1,000 volts to meet ASTM F1505-01 and IEC 60900.

The short bit on these sockets fits in spaces where height clearance is limited.

Extra-long bits allow access to hard-to-reach fasteners.

Turn many sizes of square, hex, and 8-point fasteners with one socket. Place over the fastener and 54 pins move to grip it securely.

Use bit sockets as an alternative to a screwdriver or L-key.

The short bit on these sockets fits in spaces where height clearance is limited.

The ball end allows angled entry when you don't have exact alignment between the socket bit and fastener.

These sockets are also known as pin-in-hex or pin-in-socket bits.

Use these sockets as an alternative to a screwdriver or L-key. They are made to withstand the high torque and force of impact tools.

A ratchet mechanism allows you to turn fasteners without removing and repositioning the wrench.

The handle is covered in rubber for a comfortable grip.

Also known as a construction or spud handle, wrenches use the pointed end to align bolt holes.

A gasket seals in permanent lubrication and keeps out dirt, dust, and moisture.

Twist the grip to rapidly turn a socket before final tightening or to remove a fastener once loosened. The handle also swings like a traditional ratchet wrench.

Made of aluminum-bronze, these wrenches satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Insulated to protect against accidental contact with live electrical circuits, these wrenches are tested to 1,000 volts to meet IEC 60900.

Turn sockets in the most confined spaces.

Pivot the head for access to fasteners in tight spots.

The L shape provides clearance when reaching over obstructions.

Bend around obstructions to turn hard-to-reach fasteners.

The ratcheting mechanism turns sockets quickly.

These wrenches have an accuracy of ±3.5%.

Measure with an accuracy of ±2%.

Measure with an accuracy of ±7%.

A main pointer on the dial shows torque as it’s being applied and a memory pointer indicates the maximum torque reached.

These wrenches slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

When the set torque is reached, these wrenches signal with an audible click and an impulse in the grip.

Set the desired torque and the wrench indicates when it's reached with an audible click and an impulse in the grip.

No need to pull the socket off the tool—push a button to release.

Apply more torque than your wrench can deliver on its own. Use a multiplier with a torque wrench to ensure you do not exceed the maximum input torque.

Also known as impact drivers, use these tools with impact sockets to break frozen bolts and screws free. Strike with a hammer to tighten and loosen fasteners.

These tools are suitable for general shop, maintenance, and automotive work.

Built for durability, these high-performance tools handle the demands of high-volume production and tough maintenance applications.

Use these wrenches for medium-volume production, general maintenance, and construction applications.

Set torque and the wrench will prevent you from exceeding it. These are also known as nutrunners.

Fit these adapters between your wrench and socket to enable finger tightening.

Magnets hold sockets securely in place.

Move the sliding clips to any position along the rail to hold a variety of sockets.

Hold different square drive sizes on the four clip rails stored in these trays.

The rail is smooth plastic so the clips move more easily than on steel-rail organizers.

Turn nuts on bolts and threaded rod, which can pass through the short end of the wrench. For additional leverage, slip a bar through the short end to create a T-handle.

Attach a socket to the 1/4" square drive tip. These tools have a dial that shows how torque measurements change as you turn the driver. Use to fasten to a specific torque, determine fastener torque specifications, and identify the torque required to loosen tightened fasteners.