Gravity hinges allow these doors to swing closed after being pushed open from either direction.

Access your roof from inside your building.

Designed for use with circular cutouts, these panels have gaskets that form a tight seal to keep out dust and moisture.

Install these panels in wet concrete on new floors and sidewalks to access equipment below the surface.

These thresholds have a seal to provide protection from the elements. With a ribbed top, they offer more slip resistance than smooth-top thresholds.

An antislip coating adds another layer of slip resistance to these thresholds.

The middle of these three-piece thresholds can be installed smooth or ribbed side up for more slip resistance.

Divert rain and snow away from door openings.

These closers can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

A built-in stop prevents doors from opening too far—good when wall- or floor-stops can’t be used. Designed for frequently used doors, these closers last twice as long as standard door closers. They can replace Yale, Dorma, Falcon, Stanley, Parker, and Cal-Royal models with the same mounting hole pattern.

When replacing door closers, these mounting plates let you match new closers to your existing hole patterns from most Corbin Russwin, Dorma, LCN, Norton, and Yale closers.

Hardwire these switches to automatic door openers, electromagnetic locks, and electric strikes and your door will open at the touch of a button or the wave of your hand.

These closers include a door holder, which keeps doors open with an electromagnet. When activated by a fire alarm, the magnet shuts off and releases the door.

Step on the spring-operated plunger to hold your door in place; tap on the release lever to free it.

For use with doors that already have a closer, these holders keep doors open with an electromagnet. When activated by a fire alarm, the magnet shuts off and releases the door.

Close storm doors more smoothly than standard spring closers.

Pull a chain to manually open overhead doors.

Built to withstand corrosive marine environments, track is anodized aluminum and hangers are 316 stainless steel.

Sets include an upper and lower track for hanging lightweight cabinet doors that slide past each other.

These latches withstand temperatures up to 480° or 570° F.

Rugged construction withstands impact from carts, dollies, and other equipment.

An alarm sounds when these touch bars are pushed to open doors.

Hold crossbars in the open position so traffic can pass freely through doorways.

Push to close and pull up on the latch arm to open these padlockable latches.

Lock sliding windows in a closed position, or slightly open for ventilation.

These hinges are made of metal.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

A grease fitting makes these hinges easy to lubricate.

Springs in these hinges with holes automatically swing doors and gates closed behind you.

These hinges are made of metal.

A snap-on cover protects these hinges from tampering and creates a finished appearance.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Choose these hinges for their adherence to strict military standards for material and construction.

Fortify a door's base as well as its bottom edge to guard them against damage from foot traffic and equipment. These plates can also be used to salvage rusted, rotted, or otherwise damaged doors.

For applications that require a large gripping area, these handles have a center-to-center distance of 12" or more. Fasten them directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

A rubber coating provides a comfortable grip. Cut the grip to the length you need before mounting. Fasten these handles directly to the front of your surface to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

Thread screws through holes from the back of your surface into the handles to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

With a mounting hole center-to-center distance of 1" or less, these are the smallest pull handles we offer. Thread screws through holes from the back of your surface into the handles to open and close tiny doors and drawers.

Thread screws through holes from the back of your surface into the handles to open and close a variety of doors and drawers, including those on furniture, machines, and equipment. The grip is offset from the mounting surface so there's room to fully grasp the handle.

Fasten these handles directly to the front of your surface to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment. Their grip folds out of the way when it's not in use.

These handles have a folding grip that drops out of the way when you let go. Insert studs into holes in your surface and secure from the backside to open and close a variety of doors and drawers on chests, crates, furniture, machines, and equipment.

Pull doors open with an arm or a foot—instead of your hands—to reduce the spread of germs, bacteria, and viruses. These handles are often installed on restroom doors.

Access handles from multiple angles to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

Build test fixtures, prototypes, and other small structures with this miniature version of T-slotted framing and fittings.

These kits include all brackets and fasteners needed for mounting partitions.

Design your own partitions, add to your existing partition, or replace individual components and hardware.

The two-piece design accommodates a wide range of panel thicknesses.