Aluminum Manifolds | McMaster-Carr

Filter by

Material

Aluminum

Body Material

Aluminum

Number of Outlets

Pipe Size

Thread Type

UN/UNF (SAE Straight)

Outlet Location

For Use With

Manifold Flow Pattern

Right Angle

Straight

Number of Inlets

Shape

Junction Block

Manifold

Outlet Center-to-Center

Manifold Type

Inlet/Outlet Connection

Single Section

Termination Plate

Maximum Pressure @ Temperature

Outlet Spacing

Dash Size

Length

Finish

Connects To

Fitting Connection

Connection Port

System of Measurement

Tube OD

Export Control Classification Number (ECCN)

REACH

RoHS

Compliant with Exemptions

Not Compliant

DFARS Specialty Metals

Exempt

Forward

How can we improve?

690 Products

How to Measure Threaded Pipe Size

Right-Angle Flow Rectangular Manifolds

Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

Dual-Section Right-Angle
Flow Rectangular Manifolds

These manifolds have two separate sections inside, so you can run two different substances through them without worrying about them intermixing. Also known as headers.

Straight-Flow Rectangular Manifolds

Unlike other manifolds, which have an inlet on either end, these have one inlet on the opposite side from the outlets. This design allows air or fluid to follow a straight path, improving flow through your system. Also known as headers.

Low-Profile Hex Manifolds

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Low-Profile Square Manifolds

With outlets on the side instead of on top, these manifolds have a lower profile than rectangular manifolds and fit well in cramped spaces. Use them to distribute air or fluid to three locations from a single supply source.

Round Manifolds for Hose Lines

Mount these manifolds on the end of a hose line to distribute air, water, or hydraulic fluid to three locations from a single supply source.

Color-Coded Irregular Hex Manifolds

Use these manifolds with molding equipment to circulate hot and cold water through your line. They have a red side for hot water and a blue side for cold water.

Straight-Flow Junction Blocks

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air or fluid to flow straight through the block.

Right-Angle Flow Junction Blocks

These junction blocks have threaded holes that allow air or fluid to flow at a 90° angle through the block. Use them to organize and separate multiple lines in your system.

Push-to-Connect Tube Fittings for Air

Brass Push-to-Connect Tube Fittings for Air

Made of brass, these fittings have good corrosion resistance.

Nickel-Plated Brass Push-to-Connect
Tube Fittings for Air

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

Build-Your-Own Air Hose System

With an easy-to-cut hose and push-to-connect fittings, you can install a compressed air line system in just a few hours.

Industrial Quick-Disconnect Hose Couplings for Air

The industry standard for quick-disconnect couplings, these are also known as industrial interchange couplings. Compatible with Industrial-shape plugs and sockets.

Universal Quick-Disconnect Hose Sockets for Air

Sockets accommodate five common plug shapes: Industrial, ARO, Lincoln, Tru-Flate, and European.

Lubricating

1/4" Loc-Line Coolant Hose

Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.

Flow-Adjustment Valve
Manifolds for Sealed Systems

A sealed design prevents contamination in dirty and dusty environments.

Flow-Adjustment Valve
Manifolds for Vented Systems

For use in clean environments, these manifolds have multiple air vents that keep pressure balanced.

Oil Manifolds

Deliver an equal amount of oil to multiple lubrication points at once.

Grease Fitting Manifolds

Save time by sending grease from one fitting to multiple points. These manifolds come with everything you need to set up a remote lubrication system.

Electric-, Air-, and Hydraulic-Powered Motion Control

Modular Air Directional Control
Valves with Air Manifolds

Mount valves to a single-station base or to a manifold, which allows a single pressure source for multiple valves, then add or remove valves as your needs change.

Modular Air Directional Control Valves
with Air and Electrical Manifolds

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

Two-Speed Two-Action Electrically
Operated Air Directional Control Valves

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

Two-Speed Two-Action Electrically Operated
Air Directional Control Valves with Full Shut-Off

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Two-Speed Two-Action Electrically Operated Air
Directional Control Valves with Exhausting Shut-Off

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Single-Action Electrically Operated
Air Directional Control Valves

These valves create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate. They're also known as 3/2 valves.

NFPA Valve-Mounting Blocks

NFPA valve-mounting blocks have standardized valve mounting patterns to keep hydraulic lines compact and organized.

Flow-Adjustment Screw-In Hydraulic Valves

Turn the knob to gradually adjust the amount of flow.

T-Slotted Framing Manifolds

Distribute compressed air, hydraulic fluid, or water from a single supply to multiple locations.