Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Slide the shaft in to install, then tighten to secure. For use with light to medium loads where shaft alignment is not critical, these shaft supports brace the end of a linear shaft along the ground or other flat surface.

These shaft supports hold linear shafts perpendicular to the mounting surface.

Position shafts an inch or two off the ground to maintain bearing and part clearance. Support rails provide stability over the entire length of shaft, allowing virtually unlimited travel lengths and eliminating bending under moderate to heavy loads.

These rods and discs are precision ground to offer tighter tolerances than standard 6061 rods and discs.

An anodized coating forms a bond with the aluminum surface to improve wear and corrosion resistance.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

An anodized coating forms a bond to the inside, outside, and ends of these tubes to improve wear and corrosion resistance.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The thickness is oversized to allow for finishing to exact requirements.

One side of these sheets and bars is polished to either a brushed finish or a mirror-like finish.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The outside of these 90° angles is polished to either a brushed finish or a mirror-like finish.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The outside of these tubes is anodized to improve wear and corrosion resistance.

The anodized coating on these 90° angles forms a bond with the aluminum surface to improve wear and corrosion resistance.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

As the strongest multipurpose aluminum we offer, 6013 aluminum has the same good corrosion resistance, weldability, and machinability as 6061 with increased strength. 6013 is often fabricated into high-stress machine parts.

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

These rods are precision ground and held to a strict straightness tolerance, so they’re ready for turning in a lathe.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed. It offers similar performance to 7075 aluminum, but it’s not as strong.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed. It offers similar performance to 7075 aluminum, but it’s not as strong.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

2011 has the best machinability of all the aluminum alloys. It is the most selected aluminum for screws, tube fittings, hose parts, and other items that require extensive machining.

2011 has the best machinability of all the aluminum alloys. It is the most selected aluminum for screws, tube fittings, hose parts, and other items that require extensive machining.

MIC6 is cast from a high-strength 7000-series aluminum, then stress relieved to maintain dimensional stability during high-speed machining.

A honeycomb core is bonded between two aluminum sheets for rigidity.

These tubes are sized so that each tube fits into the next larger size.

Includes one 1-1/2"×3"×0.032" thick piece of each texture: weave, diamond, and tread.

One side of these sheets is painted in your choice of gloss color, while the other side is painted gloss white.

Made of 1000 series aluminum which is 99% pure, this aluminum offers superior formability, corrosion resistance, and electrical conductivity. It's frequently fabricated into raceways, decorative trim, and other parts where strength and hardness are not required.

Use this foil as a blanket to disperse heat evenly in high-vacuum systems, as well as in clean rooms and other controlled environments where dust and oil could jeopardize a system.

Known for being one of the easiest types of aluminum to weld, 5052 is also recognized for its ability to resist salt water. It's widely used for the bodies of boats, buses, trucks, and trailers, as well as for chemical drums.

5086 aluminum is used on ships, oil rigs, tanks, and pressure vessels because of its excellent saltwater resistance and formability.

5086 aluminum is used on ships, oil rigs, tanks, and pressure vessels because of its excellent saltwater resistance and formability.

Also known as armor plate, these 5083 aluminum sheets are hardened to an H131 temper for increased strength and impact resistance over standard 5083 sheets.

Stronger than other marine-grade aluminum, 5456 is often used for pressure vessels and storage tanks in saltwater environments.

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.