From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

This material has tighter tolerances than standard 303 stainless steel.

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

With a higher chromium content than 15-5 PH stainless steel, this high-strength 17-4 PH offers better corrosion resistance. It is also known as 630 stainless steel.

The width and thickness are oversized for finishing to your exact requirements.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The thickness is oversized to allow for finishing to exact requirements.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

Choose between sheets and bars that are precision ground on all six sides or just on the top and bottom.

Substitute 7050 aluminum for 7075 in structural applications when high stress-corrosion resistance is required. It is the same material that's used for bulkheads and fuselage frames.

MIC6 is cast from a high-strength 7000-series aluminum, then stress relieved to maintain dimensional stability during high-speed machining.

Also known as flat stock, the thickness on these sheets and bars is held to a tight tolerance.

Also known as chrome-moly steel, this versatile 4140 alloy steel is used for a wide range of parts, such as gears, axles, shafts, collets, and die holders. It resists fracturing from repeated stress.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

Stronger than low-carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts.

The lead additive acts as a lubricant, which allows 12L14 carbon steel to withstand very fast machining. It's used to fabricate a wide variety of machine parts.

With the highest lead content of all the brass alloys, 360 offers the best machinability. Often called free-machining and free-cutting brass, it stands up to high-speed drilling, milling, and tapping operations with minimal wear on your tools. It’s commonly used for gears, pinions, and lock components.

Thickness and width are oversized to allow for finishing.

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

These sheets and bars are precision ground to a tight thickness tolerance.

These precision-ground sheets and bars are held to a tight thickness tolerance.

The thickness, length, and width are oversized for finishing to your exact requirements.

Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.

An economical alternative to Delrin® acetal resin, this acetal copolymer offers similar wear resistance.

More sustainable than standard UHMW, these sheets and bars are made from partially recycled material, so they have a lower carbon footprint.

Also known as Tivar H.O.T., this material lasts up to 10 times longer in high-temperature applications than standard UHMW.

The addition of glass fibers makes this material more abrasion resistant than standard UHMW. It’s also known as Tivar 88.

If a chip of this material breaks off, it can be located by metal detectors to reduce contamination risks.

Also known as nylon 6/6, this general purpose material is often used for bearings, gears, valve seats, and other high-wear parts.

The addition of MDS results in a nylon with exceptional wear resistance as well as self-lubricating properties.

Often used to make gears and wear strips, these cast nylon 6 sheets and bars withstand higher temperatures and are easier to machine than standard nylon 6/6 sheets and bars.

Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

Because this polypropylene resists swelling when exposed to water, it’s often fabricated into containers and parts for laboratory equipment.

One of the softest and most flexible plastics we offer, LDPE is more formable than HDPE.

Polycarbonate maintains good impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

Made with Teflon® PTFE resins, these sheets and bars surpass most plastics when it comes to chemical resistance and performance in extreme temperatures.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

Cast acrylic is easier to machine than extruded acrylic. It's comparable to Lucite and Plexiglas® Acrylic.