From cookware to chemical-processing equipment, 304 stainless steel is a good all-around choice for a wide range of applications.

When compared to standard 304 stainless steel, this material can be machined faster with less wear on cutting tools. It's also called Prodec and Project 70+.

Widely used for fabricating fittings and fasteners, 303 stainless steel machines quickly without sticking to cutting tools.

The addition of molybdenum gives 316 stainless steel excellent corrosion resistance. Use it in a variety of marine and chemical-processing applications.

This material is precision ground to offer tighter tolerances than standard 316 stainless steel.

With a higher chromium content than 15-5 PH stainless steel, this high-strength 17-4 PH offers better corrosion resistance. It is also known as 630 stainless steel.

This material is hardened for improved strength and wear resistance.

Often used for fasteners and valves, 410 stainless steel withstands wear caused by abrasion.

Also called flat stock, these precision-ground bars are held to tight thickness and width tolerances.

One of the hardest types of stainless steel after heat treating, 440C offers excellent wear and abrasion resistance. It's often used for bearings, valves, and knife blades.

The titanium content of 321 stainless steel preserves corrosion resistance around weld points.

Able to withstand temperatures up to 2100° F, 330 stainless steel is widely used as components for industrial furnaces, gas turbines, and boilers. It resists cracking when exposed to heating and cooling cycles.

The most widely used aluminum, 6061 is fabricated into everything from pipe fittings and containers to automotive and aerospace parts. It is strong and corrosion resistant, plus it's easy to machine and weld.

The thickness is oversized to allow for finishing to exact requirements.

One side of these sheets and bars is polished to either a brushed finish or a mirror-like finish.

More corrosion resistant and easier to form than multipurpose 6061 aluminum, 6063 is primarily used for exterior railings, decorative trim, and door frames.

Known for being one of the easiest types of aluminum to weld, 5052 is also recognized for its ability to resist salt water. It's widely used for the bodies of boats, buses, trucks, and trailers, as well as for chemical drums.

3000 series aluminum stands up to outdoor use, as well as exposure to chemicals. It offers a good combination of strength, formability, and weldability. It's often used for storage tanks, heat exchangers, garage doors, and general sheet metal work.

A honeycomb core is bonded between two aluminum sheets for rigidity.

Highly corrosion resistant, 5083 is largely used around salt water for building ships and oil rigs. It maintains its strength in extreme cold, so it's also used to make cryogenic pressure vessels and tanks.

While 2024 aluminum was initially designed for structural components in aircraft, it's now widely used when a high strength-to-weight ratio is needed, such as for gears, shafts, and fasteners. It offers similar performance to 7075 aluminum, but it’s not as strong.

Originally developed for aircraft frames, uses for 7075 aluminum now include keys, gears, and other high-stress parts. It is often used as a replacement for 2024 aluminum because it’s stronger and provides similar performance in all other aspects.

MIC6 is cast from a high-strength 7000-series aluminum, then stress relieved to maintain dimensional stability during high-speed machining.

Also known as mild steel, low-carbon steel is easy to machine, form, and weld. It's widely fabricated into parts that don’t require high strength.

With a thickness that's precision ground to a tight tolerance, these bars are sometimes called flat stock.

This UHSS (ultra high-strength steel) allows you to fabricate high-strength parts using thinner material than you could with other types of steel. It is formable, weldable, and more economical than alloy steel.

Exceptional hardness makes AR500 carbon steel more resistant to wear and impact than other carbon steel.

Even in low temperatures, A516 carbon steel resists breaking upon impact. Also known as pressure-vessel-quality (PVQ) steel, it is mostly used for boilers, storage tanks, and pressure vessels.

Also known as flat stock, the thickness on these sheets and bars is held to a tight tolerance.

Also known as chrome-moly steel, this versatile 4140 alloy steel is used for a wide range of parts, such as gears, axles, shafts, collets, and die holders. It resists fracturing from repeated stress.

4130 alloy steel has a low carbon content for good weldability. It's often used for gears, fasteners, and structural applications.

Heat treated for enhanced hardness and strength, A514 alloy steel is suitable for structural applications and supporting heavy loads.

The most formable brass we offer, 260 offers better weldability than 300 series brass but it’s not as machinable. Sometimes called cartridge brass, it's commonly used for ammunition casings, radiator components, and decorative door hardware.

353 brass is more formable than 385 brass while maintaining good machinability. Commonly called engraver’s brass, it’s well suited for fabrication processes such as knurling and threading. Use it to make nuts, gears, drawer pulls, and hinges.

Polished on one side to a reflective, mirror-like finish.

Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.

These bars are precision ground on the top and bottom for a tight thickness tolerance of ±0.002".

Precision ground on the top and bottom, these bars have a tight thickness tolerance of ±0.002".

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

Offering high electrical conductivity and formability, 110 copper is 99.9% pure. Also known as ETP copper, it's often used in electrical applications, such as for bus bars and wire connectors, as well as for flashing, gaskets, and rivets.

One side of these sheets has a brushed finish with grain lines running in one direction to mask fingerprints.

182 copper is stronger, harder, and more wear resistant than 110 copper. Also known as RWMA Class 2 chromium copper, it's commonly used in resistance welding, for circuit-breaker parts, and for molds to make plastic parts.

Because Grade 2 titanium is 99% pure, it is more corrosion resistant than Grades 5 and 9 but not as strong. It has good formability and weldability. Common uses include chemical processing equipment, heat exchangers, and marine hardware.

A blend of nickel, chromium, and molybdenum gives these 625 nickel sheets the strength, weldability, and corrosion resistance necessary for use in expansion joints, exhaust systems, and marine components. They are comparable to Inconel 625 and Haynes 625.

C-276 nickel has excellent corrosion resistance against chemicals, including nitric acid, sulfuric acid, and hydrochloric acid.

These sheets and bars are precision ground to a tight thickness tolerance.

These precision-ground sheets and bars are held to a tight thickness tolerance.

These bars are precision ground to a tight thickness tolerance.

These W1 bars have lower amounts of alloy elements than other tool steels for excellent machinability.

The thickness, length, and width are oversized for finishing to your exact requirements.

The thickness on these bars is precision ground to a tight tolerance.

These bars are also known as flat stock.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

This material suppresses static charges to prevent dust from building up.

The addition of carbon gives this material the ability to divert static electricity faster than antistatic UHMW.

Compared to our standard UHMW polyethylene, these sheets and bars hold up better to scuffs and scrapes in high-speed, high-precision, and high-impact applications—such as conveyor equipment, chute liners, and machine guards. Also known as Tivar HPV.

This oil-filled material is self-lubricating for an extra-slippery surface.

Also known as starboard, these sheets and bars won’t degrade when exposed to salt water, humidity, and UV light.

Made of recycled HDPE plastic, these sheets are more sustainable and economical than standard marine-grade moisture-resistant HDPE sheets.

Because PVC resists many acids and alkalies, it’s widely used for tanks and in chemical-processing applications. Also known as PVC Type 1.

Widely used for vehicle interiors and equipment housings, this blended material maintains its physical properties after thermoforming. It is comparable to Kydex.

Create signs and partitions with this easy to cut PVC foam.

This nylon 6/6 material is modified with MDS for a self-lubricating surface that’s more slippery than standard nylon. It's often used in high-friction applications, such as gears and bearings.

With glass reinforcement, this nylon 6/6 material is stronger than standard nylon, plus it can withstand higher temperatures. It’s widely used in high-stress applications, such as caster wheels and automotive parts.

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.

The combination of high strength and water resistance, along with a variety of color choices, makes this opaque cast acrylic useful for outdoor signs and containers. It's also known as Lucite and Plexiglas® Acrylic.

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

This material prevents the buildup of static charges.

Widely used in semiconductor applications, this polypropylene meets UL flame-retardance standards.

Often fabricated into signs, packaging, and light duty housings, polystyrene is easy to thermoform.

Polyester resists swelling in wet environments.

Made with virgin Teflon® PTFE resins, these sheets and bars surpass most plastics when it comes to chemical resistance and performance in extreme temperatures.

Manufactured from Rulon PTFE, a PTFE material that's modified with epoxy-coated fiber for a super-slippery, impact-resistant surface that resists wear.

Protect sensitive equipment from damaging electrical static charges.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

Just as chemical resistant as PTFE, yet FEP offers greater impact strength. Use it to make valve components and gaskets.

Filled with glass, these Torlon 5030 bars are stronger and more rigid than Torlon 4301 and 4203, yet still electrically insulate like Torlon 4203.

Choose these sheets over standard Torlon PAI for their excellent electrical insulating properties.

Cast acrylic is easier to machine than extruded acrylic. It's comparable to Lucite and Plexiglas® Acrylic.

A static-dissipative coating on this cast acrylic prevents electrostatic discharge from damaging sensitive electronic equipment.

Modified for increased impact strength over other types of acrylic, this acrylic is often used for skylights and outdoor signs.

With a clear coating that provides protection from abrasion, UV light, and harsh cleaners, this polycarbonate is often used to create transit shelters and equipment shields.

This polycarbonate has a static-dissipative coating that prevents electrostatic discharge from damaging sensitive electronic equipment.