One-third the weight of steel, aluminum screws resist corrosion in wet environments.

Made from aluminum, these metric screws are lightweight and resist corrosion in wet environments. The flange is wider and thicker than our other flanged screws, so they distribute pressure the best.

Aluminum screws are lightweight and have good corrosion resistance.

One-third the weight of steel, aluminum screws resist corrosion in wet environments.

One-third the weight of steel, aluminum shoulder screws are lightweight and have good corrosion resistance.

Install and remove these shoulder screws by hand or with a hex key.

These slotted thumb screws have a thin, knurled head for use in low-clearance applications. Made of 18-8 stainless steel, they are chemical resistant.

These metric thumb screws have a thin, knurled head for use in low-clearance applications. They have a black-oxide finish to resist corrosion in dry environments.

Brass thumb screws are corrosion resistant in wet environments and electrically conductive.

Brass thumb screws are corrosion resistant in wet environments and electrically conductive.

Made from 18-8 stainless steel, these thumb screws are chemical resistant. They have a raised head that makes them easy to grip.

A raised head makes these thumb screws easy to grip. They have a black-oxide finish to resist corrosion in dry environments.

Brass thumb screws are corrosion resistant in wet environments and electrically conductive.

These slotted thumb screws are slim to fit in tight spaces.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

A knurled head allows for slip-resistant controlled adjustment.

Arms provide a flat surface to push your fingers against.

These metric thumb screws have a large head that allows you to grip them with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

Fine threads give you precise control.

Fasten material by hand, so tools don’t scratch or contaminate parts you frequently adjust in food-processing or pharmaceutical plants.

A flange provides a bearing surface to hold parts under the head.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

These metric thumb screws have wings that provide more leverage than spade-head thumb screws for greater torque while tightening. A zinc plating provides corrosion resistance in wet environments.

Made from 18-8 stainless steel, these thumb screws are chemical resistant. Also known as dog- and pilot-point thumb screws, insert the point into a drilled hole or slot to hold items in place.

Arms provide a flat surface to push your fingers against.

A wide tip provides more gripping power than standard swivel-tip thumb screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.

A large swivel angle allows these thumb screws to make better contact with angled and uneven surfaces than nonremovable swivel-tip thumb screws.

A raised head makes these thumb screws easy to grip. Made from nylon, they're chemical resistant, nonconductive, and lightweight.

These nylon thumb screws are chemical resistant, nonconductive, and lightweight.

Stainless steel thumb screws have excellent corrosion resistance in most environments.

The head fits through a slit in a latch or panel to hold it in place.

Add length to a binding barrel.

Install these thumb-screw-head screws through a hole and thread on a retainer to keep secure—no special tools are required.

Snap these screws into panels up to 0.125" thick—no tools are required for installation.

Press these wing head nuts into a closed-end hole or thick panel in applications where the back of the panel is inaccessible. A quarter-turn locks and releases access panels, doors, and covers.

Rivet these wing head nuts into thin panels for a flush fit. They can be mounted without space between panels. A quarter-turn locks and releases access panels, doors, and covers.

An expanding rubber bushing damps vibration while holding panels together.

In addition to joining male- and female-threaded parts, these adapters can increase or decrease metric thread sizes and change the thread pitch.

Need to join two female-threaded parts, such as coupling nuts, with dissimilar inch thread sizes? Attach them to these adapters and tighten the exterior hex nut for a secure connection.

One side inch, one side metric, and a hex in the middle—these handy fasteners connect two female-threaded parts, such as coupling nuts, adapting from inch threads to metric. Tighten with a standard wrench.

Increase or decrease metric thread size from one male-threaded part to another. Commonly used to connect two differently sized threaded rods, they have a hex-shaped body, so you can tighten them with a standard wrench.

Adapt threaded rods from inch to metric. These adapters connect two male-threaded fasteners, so you can change the gender of a mating part or increase or decrease its thread size. The hex-shaped body fits into the head of a standard wrench.

The grooves in these pins grip plastics and other soft materials. Press them in to hold panels together. Also known as PEM® TKA and TK4 TackSert pins.

The domed top allows you to firmly hold these knobs in the palm of your hand to position, tighten, and hold fixtures, equipment, and machinery. Mount them into a threaded hole.

Convert screws into knobs so large you can grip them with heavy work gloves. Slip these knobs onto a hex or socket head screw and tighten the set screw to secure. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

The domed top allows you to firmly hold these knobs in the palm of your hand to position, tighten, and hold fixtures, equipment, and machinery. Install these knobs on a threaded stud.

The domed top allows you to firmly hold these knobs in the palm of your hand. Mill specific holes or keyways in the hub to meet your specifications, or weld in place. Use these knobs to position, tighten, and hold fixtures, equipment, and machinery.

Long shafts can thread through these knobs for mounting versatility. The knobs provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

A handle makes these knobs easy to turn. Tap custom threads or secure with a set screw to provide a firm grip to position, tighten, and hold fixtures, equipment, and machinery.

The mounting plate provides a flat surface for supporting loads.

Install these nuts on a rotary shaft to create a linear positioning system without a lead screw. Instead of threads, a set of angled ball bearings drives the nut along a shaft as it spins.

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.