Anchor Type Anchor Type |
---|
![]() | ![]() |
Stud | Female Threaded |
![]() | ![]() |
Toggle | Tapping Screw |
![]() | |
Tube |
For Use In For Use In | Show |
---|
|
For Use In For Use In | Hide |
---|
|
|
Pull-Out Strength Pull-Out Strength |
---|
|
Material Material |
---|
|
Usable Length Usable Length |
---|
|
|
Toggle Material Toggle Material |
---|
|
Shear Strength Shear Strength |
---|
|
Drive Style Drive Style |
---|
![]() | ![]() | ![]() |
Phillips | Slotted | External Hex |
Drill Bit Decimal Size Equivalent Drill Bit DecimalSize Equivalent |
---|
|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
---|
Sleeve Material Sleeve Material |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
About Structural Adhesives
More
Female-Threaded Expansion Anchors for Hollow Block and Brick

For narrow holes and small cavities where toggle anchors won't fit. To install, tap the anchor cone first into a drilled hole. Then, insert a screw or threaded rod and tighten. Pull-out strength and shear strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
Strength, lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Size | Lg. | Drill Bit Size | Min. Installation Dp. | Sleeve Material | Pull-Out | Shear | Tested In | Specifications Met | For Use In | Pkg. Qty. | Pkg. | |
Steel | ||||||||||||
1/4"-20 | 7/8" | 3/8" | 3/4" | 304 Stainless Steel | 260 | 300 | 4,000 psi Concrete | __ | Concrete, Hollow Block, Hollow Brick | 1 | 000000000 | 00000 |
1/4"-20 | 7/8" | 3/8" | 3/4" | Zinc Alloy | 270 | 300 | 4,000 psi Concrete | __ | Concrete, Hollow Block, Hollow Brick | 5 | 000000000 | 00000 |
5/16"-18 | 1 5/16" | 5/8" | 1" | Zinc Alloy | 400 | 470 | 4,000 psi Concrete | __ | Concrete, Hollow Block, Hollow Brick | 5 | 000000000 | 00000 |
3/8"-16 | 1 5/16" | 5/8" | 1" | 304 Stainless Steel | 450 | 620 | 4,000 psi Concrete | __ | Concrete, Hollow Block, Hollow Brick | 1 | 000000000 | 0000 |
3/8"-16 | 1 5/16" | 5/8" | 1" | Zinc Alloy | 500 | 620 | 4,000 psi Concrete | FM Approved, UL Listed | Concrete, Hollow Block, Hollow Brick | 5 | 000000000 | 00000 |
1/2"-13 | 1 3/4" | 3/4" | 1 1/2" | Zinc Alloy | 1,000 | 1,000 | 4,000 psi Concrete | FM Approved, UL Listed | Concrete, Hollow Block, Hollow Brick | 1 | 000000000 | 0000 |
5/8"-11 | 2" | 1" | 2 1/4" | Zinc Alloy | 2,300 | 1,600 | 4,000 psi Concrete | FM Approved, UL Listed | Concrete, Hollow Block, Hollow Brick | 1 | 000000000 | 0000 |
Female-Threaded Toggle Anchors for Hollow Block and Brick

A pivoting toggle bar creates a strong hold. These anchors provide an internally threaded socket connection for threaded rods and bolts. To install, push through a drilled hole; gravity drops the toggle into position. Anchors are removable and reusable. Made from zinc yellow-chromate plated steel, they resist corrosion in wet environments. Pull-out strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
Thread | Strength, lbs. | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
Size | Dp. | Lg. | Usable Lg. | Wing Span | Drill Bit Size | Pull-Out | Shear | Tested In | For Use In | Each | |
Zinc Yellow-Chromate Plated Steel | |||||||||||
3/8"-16 | 1/2" | 2" | 1 1/2" | 2" | 1/2" | 800 | Not Rated | 1,500 psi Concrete | Concrete, Hollow Block, Hollow Brick | 000000000 | 000000 |
1/2"-13 | 11/16" | 2 1/4" | 1 5/8" | 2" | 5/8" | 1,400 | Not Rated | 1,500 psi Concrete | Concrete, Hollow Block, Hollow Brick | 000000000 | 00000 |
Stud-Style Anchors for Hollow Block and Brick

These stud-style anchors include a nut and a washer. To install, push through a drilled hole; gravity drops the toggle into position. Anchors are removable and reusable. Made from zinc yellow-chromate plated steel, they resist corrosion in wet environments. Pull-out strength and shear strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
Thread | Strength, lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Lg. | Usable Lg. | Size | Lg. | Wing Span | Washer OD | Drill Bit Size | Pull-Out | Shear | Tested In | Thread Fit | For Use In | Pkg. Qty. | Pkg. | |
Zinc Yellow-Chromate Plated Steel | ||||||||||||||
1/4" Dia. | ||||||||||||||
1 3/4" | 1" | 1/4"-20 | 5/8" | 1" | 0.625" | 5/16" | 170 | 370 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 00000 |
2 1/2" | 1 3/4" | 1/4"-20 | 1" | 1" | 0.625" | 5/16" | 170 | 370 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 0000 |
3 1/4" | 2 1/2" | 1/4"-20 | 1 7/8" | 1" | 0.625" | 5/16" | 170 | 370 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 0000 |
5/16" Dia. | ||||||||||||||
2 1/2" | 1 1/2" | 5/16"-18 | 1 1/8" | 1 1/4" | 0.688" | 5/16" | 220 | 570 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 0000 |
3 1/4" | 2 1/4" | 5/16"-18 | 1 3/4" | 1 1/4" | 0.688" | 5/16" | 220 | 570 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 00000 |
3 3/4" | 2 3/4" | 5/16"-18 | 1 5/8" | 1 1/4" | 0.688" | 5/16" | 220 | 570 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 00000 |
3/8" Dia. | ||||||||||||||
3 1/4" | 2" | 3/8"-16 | 1 7/8" | 1 1/2" | 0.813" | 3/8" | 250 | 750 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 00000 |
3 3/4" | 2 1/2" | 3/8"-16 | 1 5/8" | 1 1/2" | 0.813" | 3/8" | 250 | 750 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 00000 |
4" | 2 3/4" | 3/8"-16 | 1 7/8" | 1 1/2" | 0.813" | 3/8" | 250 | 750 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 2 | 000000000 | 0000 |
4 1/2" | 3 1/8" | 3/8"-16 | 3 1/4" | 1 1/2" | 0.813" | 3/8" | 250 | 750 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 4 | 000000000 | 00000 |
6" | 4 1/2" | 3/8"-16 | 3 1/2" | 1 1/2" | 0.813" | 3/8" | 450 | 750 | 1,500 psi Concrete | Class 2A | Concrete, Hollow Block, Hollow Brick | 1 | 000000000 | 0000 |
Adhesive Anchor Screen Tubes for Hollow Block and Brick



Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors. To install, first fill tubes with adhesive (sold separately) and press them into a drilled hole. Hold tubes in place by pressing the tab against your block, and insert a rod into them. The rod will push the adhesive out of the mesh screen, forming a plug that keeps the rod in place once the adhesive dries.
For technical drawings and 3-D models, click on a part number.

Container Size, oz. | Begins to Harden | Reaches Full Strength | No. of 1/2" Dia. Rods Set at 4 1/2" Installation Dp. | Ultimate Pull-Out Strength (in 4,000 psi Concrete) | Mix Ratio | Consistency | Temp. Range, °F | Color | Each | |
9.5 | 5 min. @ 70° F | 45 min. | 25 in 9/16" dia. hole | 10,900 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 17,100 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 26,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 29,500 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 44,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 48,000 lbs.—1" threaded rod dia. × 9" installation dp. 56,500 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 10:1 | Paste | 15° to 110° | Gray | 0000000 | 000000 |
High-Strength Toggle Anchors

These high-strength toggle anchors provide an extremely strong hold and stay in position when a bolt is removed. To install, push the toggle through a drilled hole and pull the anchor back toward you until the toggle rests flush against the wall. Then, slide the cap up to the wall and snap off the straps. Next, position your fixture, insert a screw and tighten. For use with machine screws; minimum screw length is the wall and fixture thicknesses plus 1/2". Pull-out strength and shear strength values are 25% of the ultimate values.
Zinc-plated steel toggle anchors resist corrosion in wet environments.
18-8 stainless steel toggle anchors are chemical resistant and may be mildly magnetic.
For technical drawings and 3-D models, click on a part number.
Strength, lbs. | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Thread Size | Thread Pitch, mm | Usable Lg. Range | Wing Span | Drill Bit Size | Material | Color | Pull-Out | Shear | Tested In | Drive Style | Head Type | For Use In | Pkg. Qty. | Pkg. | |
Zinc-Plated Steel Toggle | |||||||||||||||
10-24 | __ | 3/8"-3 5/8" | 2" | 1/2" | Polystyrene Plastic | White | 200 | 200 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 10 | 000000000 | 000000 |
10-24 | __ | 3/8"-3 5/8" | 2" | 1/2" | Polystyrene Plastic | White | 200 | 200 | Hollow Concrete Block | Phillips, Slotted | Flat | Drywall, Hollow Block, Plaster, Wood Paneling | 10 | 000000000 | 00000 |
10-24 | __ | 3/8"-3 5/8" | 2" | 1/2" | Polystyrene Plastic | White | 200 | 200 | Hollow Concrete Block | Phillips, Slotted | Rounded | Drywall, Hollow Block, Plaster, Wood Paneling | 10 | 000000000 | 00000 |
10-24 | __ | 2"-9 1/2" | 2" | 1/2" | Polystyrene Plastic | White | 200 | 200 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 00000 |
1/4"-20 | __ | 3/8"-3 5/8" | 2" | 1/2" | Polystyrene Plastic | White | 250 | 250 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 10 | 000000000 | 00000 |
1/4"-20 | __ | 3/8"-3 5/8" | 2" | 1/2" | Polystyrene Plastic | White | 250 | 250 | Hollow Concrete Block | Phillips, Slotted | Flat | Drywall, Hollow Block, Plaster, Wood Paneling | 10 | 000000000 | 00000 |
1/4"-20 | __ | 3/8"-3 5/8" | 2" | 1/2" | Polystyrene Plastic | White | 250 | 250 | Hollow Concrete Block | Phillips, Slotted | Rounded | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 0000 |
1/4"-20 | __ | 2"-9 1/2" | 2" | 1/2" | Polystyrene Plastic | White | 250 | 250 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 00000 |
5/16"-18 | __ | 3/8"-2 1/2" | 2" | 3/4" | Polystyrene Plastic | White | 350 | 350 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 10 | 000000000 | 00000 |
3/8"-16 | __ | 3/8"-2 1/2" | 2" | 3/4" | Polystyrene Plastic | White | 400 | 400 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 00000 |
1/2"-13 | __ | 3/8"-2 1/2" | 2" | 3/4" | Polystyrene Plastic | White | 500 | 500 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 00000 |
M5 | 0.8 | 10mm-92mm | 51mm | 13 mm | Polystyrene Plastic | White | 200 | 200 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 0000 |
M6 | 1 | 10mm-92mm | 51mm | 13 mm | Polystyrene Plastic | White | 250 | 250 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 0000 |
M8 | 1.25 | 10mm-64mm | 51mm | 19 mm | Polystyrene Plastic | White | 300 | 350 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 00000 |
M10 | 1.5 | 10mm-64mm | 51mm | 19 mm | Polystyrene Plastic | White | 400 | 400 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 5 | 000000000 | 00000 |
18-8 Stainless Steel Toggle | |||||||||||||||
10-24 | __ | 3/8"-3 5/8" | 2" | 1/2" | Polystyrene Plastic | White | 200 | 200 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 1 | 000000000 | 0000 |
10-24 | __ | 2"-9 1/2" | 2" | 1/2" | Polystyrene Plastic | White | 200 | 200 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 1 | 000000000 | 0000 |
1/4"-20 | __ | 3/8"-3 5/8" | 2" | 1/2" | Polystyrene Plastic | White | 250 | 250 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 1 | 000000000 | 0000 |
1/4"-20 | __ | 2"-9 1/2" | 2" | 1/2" | Polystyrene Plastic | White | 250 | 250 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 1 | 000000000 | 0000 |
3/8"-16 | __ | 3/8"-2 1/2" | 2" | 3/4" | Polystyrene Plastic | White | 250 | 250 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 1 | 000000000 | 0000 |
1/2"-13 | __ | 3/8"-2 1/2" | 2" | 3/4" | Polystyrene Plastic | White | 500 | 500 | Hollow Concrete Block | __ | __ | Drywall, Hollow Block, Plaster, Wood Paneling | 1 | 000000000 | 0000 |
Tapping Screw Assortments for Concrete, Block, and Brick
Also known as Tapcons, these screws are often used to anchor parts to concrete, block, and brick. Screws have a hex head that allows for a secure grip with a wrench. Drive them into a hole with a hammer drill or socket wrench, or use a specialized installation tool (sold separately). Made from ultra-corrosion-resistant coated steel, they resist corrosion in wet environments. Length is measured from under the head.


Number of Pieces | Hex Head Screws Included | Tools Included | Container Type | Each | |
Blue Ultra-Corrosion-Resistant Coated Steel | |||||
---|---|---|---|---|---|
For Hammer Drill | |||||
176 | 1/4" × 1 1/4" Lg. (50 Pieces) 1/4" × 1 3/4" Lg. (50 Pieces) 1/4" × 2 1/4" Lg. (50 Pieces) 1/4" × 2 3/4" Lg. (25 Pieces) | Drill Bit | Plastic Box | 000000000 | 000000 |
For Rotary Drill | |||||
176 | 1/4" × 1 1/4" Lg. (50 Pieces) 1/4" × 1 3/4" Lg. (50 Pieces) 1/4" × 2 1/4" Lg. (50 Pieces) 1/4" × 2 3/4" Lg. (25 Pieces) | Drill Bit | Plastic Box | 000000000 | 00000 |

Includes | Each | |
No. 2 Socket 3/16" Hex Socket 1/4" Hex Socket 1/8" Hex Key Drill Adapter 1/2" dia. × 6" lg. Drive Sleeve | 000000000 | 0000000 |