These steel anchors are available with corrosion-resistant finishes.

A zinc plating provides corrosion resistance in wet environments.

An open-end cap nut provides a finished appearance.

Drive these tools with a hammer until the thicker portion of the tool makes contact with the anchor, causing it to expand.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

An adjustable stop allows you to set anchors at consistent depths. Use with a hammer.

Use in applications requiring high strength.

A zinc plating provides corrosion resistance in wet environments.

Turn the bolt to expand the nut for a secure hold in concrete. These anchors are often used to anchor machinery.

For narrow holes and small cavities where toggle anchors won't fit.

These steel anchors are available with corrosion-resistant finishes.

A drilled hole is required for installation.

Bolts are beveled under the head for use in countersunk holes.

Also known as Tapcons, use these screws in applications requiring high strength.

These blue and silver ultra-corrosion-resistant coated steel screws stand up to wet environments.

The spring holds the washer and toggle against opposite sides of the wall, so everything's in position before you begin tightening. Once tightened, the spring adds vibration resistance.

You can use these versatile hangers in a threaded hole (as you would a screw), or secure them with a nut (as you would a bolt).

These hangers have internal threads for use with threaded rods, bolts, and anchors.

Made from steel comparable to Grade 5 steel, these bolts are suitable for most work-holding applications.

A wing-like toggle holds against the back of the material and spreads the force over a large area to hold 30 lbs. or more.

These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.

Sew webbing onto these plates for a permanent anchor point or run webbing through to use them as guides.

Use these plates where full lengths of track won't fit to create one anchor point.

Install directly into a mounting surface to suspend threaded rod from ceilings and walls.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Route pipe, tubing, and conduit across strut channel.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Support vertical pipes passing through floors.

Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.

These clamps rotate 360° and pivot 45° to ensure the rod hangs straight, even on sloped beams.

Add a crossbeam for hanging lifting equipment, creating overhead conveyor systems, and supporting structural applications.

Clamp to both sides of a beam to add an anchor point for hoists and other overhead equipment.

Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

For a strong, secure connection, mount these hangers by welding them to a rod.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

Anchor these ringbolts where you need them, then remove the ring when not in use. Once installed, the mounting bolt stays in place. Insert the ring by threading into the mounting bolt; remove by unthreading it.

Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.

Bolt directly to a pipe flange to suspend a run of pipe above the ground.

Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.

Constructed with a saddle for both the long (live) end and the short (dead) end, these clamps apply equal pressure without crimping or crushing the wire rope, so orientation doesn't matter. Also known as fist grip wire rope clips.

Install these clamps without any specific orientation, slide the nut over the rope and tighten it onto the threaded halves with a torque wrench.

A clamp and thimble in one convenient fitting simplifies installation while providing support and fray protection to the wire rope loop. Use a torque wrench to tighten the clamp.

Also known as heavy-pattern thimbles, these can be used to reinforce the loop of a sling in accordance with ASME B30.9.

Install these swivel-hook-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Install these stud-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.

Also known as nut eyebolts, these are designed for through-hole applications.

Also known as screw eyes, use the sharp point of these eyebolts to mount directly into wood.

Attach these clamps by running a wire rope through the jaws to create an attachment point anywhere along the wire rope.

Secure grating to your support structure.

Made of steel, these durable lanyards hold up in abrasive and high-heat applications.