Selecting Clamps Using Pipe, Conduit, or Tubing Trade Size
More
About Lifting with Hoist Rings
More
About Turnbuckles and End Fittings
More
Steel Stud Anchors for Concrete
Also known as wedge anchors, the base expands as you tighten the nut for a secure hold in concrete. They're often used to anchor machinery. Pull-out strength and shear strength values are 25% of the ultimate values.
Zinc-plated and zinc yellow-chromate plated steel anchors are corrosion resistant in wet environments.
Galvanized steel anchors are more corrosion resistant than zinc-plated steel anchors. They must be used with other galvanized fasteners.
ICC listed anchors are often required for new construction. Anchors listed for cracked concrete are often required in environments which may cause concrete to crack during the life of the anchor.
For technical drawings and 3-D models, click on a part number.
Strength, lbs. | Each | Package | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Lg. | Thread Size  | Min. Thread Lg. | Washer OD | Nut Wd. | Drill Bit Size | Min. Installation Dp. | Pull-Out | Shear | Tested In | Required Installation Torque, ft.-lbs. | Certification | Each | Pkg. Qty. | Pkg. | ||
Zinc-Plated Steel | ||||||||||||||||
1 1/4" Dia. | ||||||||||||||||
| 9" | 1 1/4"-7 | 4 3/4" | 2 1/2" | 1 7/8" | 1 1/4" | 5 5/8" | 6,007 | 7,275 | 4,000 psi Concrete | 375 | ICC-ES Listed | 000000000 | 000000 | 4 | 000000000 | 0000000 |
| 12" | 1 1/4"-7 | 7 3/4" | 2 1/2" | 1 7/8" | 1 1/4" | 5 5/8" | 6,007 | 7,275 | 4,000 psi Concrete | 375 | ICC-ES Listed | 000000000 | 00000 | 4 | 000000000 | 000000 |
Galvanized Steel | ||||||||||||||||
1 1/4" Dia. | ||||||||||||||||
| 9" | 1 1/4"-7 | 2 3/4" | 3" | 1 7/8" | 1 1/4" | 5 5/8" | 7,190 | 11,750 | 4,000 psi Concrete | 400 | __ | 000000000 | 00000 | 4 | 000000000 | 000000 |
| 12" | 1 1/4"-7 | 2 3/4" | 3" | 1 7/8" | 1 1/4" | 5 5/8" | 7,190 | 11,750 | 4,000 psi Concrete | 400 | __ | 000000000 | 00000 | 4 | 000000000 | 000000 |
Pivoting Threaded-Rod-Mount Loop Hangers
Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling. To mount, slide threaded rod into the unthreaded hole on top of the hanger and secure with a nut (sold separately). When used with threaded rod, the hanging height can be adjusted after material is installed.
Zinc-plated steel hangers have good corrosion resistance. 304 stainless steel hangers have excellent corrosion resistance and good chemical resistance.
For technical drawings and 3-D models, click on a part number.
ID | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Inch | Metric, mm | For Pipe Size | For Thread Size | Cap., lbs. | Lg. | Wd. | Ht. | Thick. | Mounting Hole Dia. | Includes | Specifications Met | Each | |
Zinc-Plated Steel | |||||||||||||
| 20" | 508 | 20 | 1 1/4"-7 | 4,800 | 22 7/16" | 3" | 30" | 5/8" | 1 5/16" | Closure Bolt and Nut | Fed. Spec. WW-H-171, Type 1 MSS-SP-58, Type 1 | 00000000 | 0000000 |
304 Stainless Steel | |||||||||||||
| 20" | 508 | 20 | 1 1/4"-7 | 4,800 | 26" | 3" | 27 1/2" | 3/8" | 1 5/16" | Closure Bolt and Nut | MSS-SP-58, Type 1 | 00000000 | 000000 |
| 24" | 610 | 24 | 1 1/4"-7 | 4,800 | 30 1/2" | 3" | 31 3/4" | 3/8" | 1 5/16" | Closure Bolt and Nut | MSS-SP-58, Type 1 | 00000000 | 000000 |
Hoist Rings—For Lifting
Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque wrenches are sold separately.
Black-oxide steel hoist rings have mild corrosion resistance.
Nickel-plated steel hoist rings are more corrosion resistant than black-oxide steel hoist rings.
High-visibility hoist rings are fluorescent green, so they’re easy to distinguish from other hardware when attached to equipment being lifted.
Hoist rings that are CE marked meet European safety standards.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
| Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vertical Capacity, lbs. | Movement | Specifications Met | Each | |
Forged Black-Oxide Steel | ||||||||
|---|---|---|---|---|---|---|---|---|
| 1 1/4"-7 | 1 7/8" | 3 1/2" | 11 1/8" | 15,000 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 0000000 |
| 1 1/4"-7 | 1 7/8" | 4" | 11 1/8" | 15,000 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
| 1 1/4"-7 | 1 15/16" | 3 1/2" | 10 5/8" | 15,000 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
| 1 1/4"-7 | 2 5/8" | 4" | 11 7/8" | 15,000 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
Forged Fluorescent Green Powder-Coated Steel—High Visibility | ||||||||
| 1 1/4"-7 | 1 7/8" | 4" | 11 1/8" | 15,000 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
Forged Nickel-Plated Steel | ||||||||
| 1 1/4"-7 | 1 7/8" | 4" | 11 1/8" | 15,000 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked, MIL-STD-1365, MIL-STD-209 | 0000000 | 000000 |
Swivel-Under-Load Hoist Rings—For Lifting
The ball bearing on these hoist rings makes it easy to rotate your load even after it’s suspended. For unbalanced or heavy loads, the base also swivels to compensate for pitch, roll, and sway. Their lifting ring pivots 180° front to back. Ideal for angular lifting, these hoist rings withstand stresses that bend or break eyebolts.
Install the base of these hoist rings flush to your mounting surface. Use a torque wrench to tighten to the recommended torque stamped on the ring.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
| Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vertical Capacity, lbs. | Movement | Specifications Met | Each | |
Yellow Powder-Coated Steel | ||||||||
|---|---|---|---|---|---|---|---|---|
| 1 1/4"-7 | 1 7/8" | 2 1/8" | 10 11/16" | 21,160 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked | 0000000 | 0000000 |
Removable-Shackle Hoist Rings—For Lifting
 | 180° Pivot |
360° Swivel |
Remove the shackle after lifting while keeping the base installed for future use. Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. Install the base of the hoist ring flush to the mounting surface and tighten to the recommended torque that is stamped on the ring. Torque Wrenches are sold separately.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
| Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vertical Capacity, lbs. | Movement | Specifications Met | Each | |
Black-Oxide Steel Base with Zinc-Plated Steel Eye | ||||||||
|---|---|---|---|---|---|---|---|---|
| 1 1/4"-7 | 1 7/8" | 2 3/4" | 10 1/8" | 15,000 | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked | 0000000 | 0000000 |
Tension-Indicating Hoist Rings—For Lifting
An indicator dot changes from red to black when these hoist rings are properly tightened, eliminating the need for a torque wrench. The dot changes back to red if the hoist ring comes loose. Ideal for angular lifting, these hoist rings withstand stresses that bend or break eyebolts. They have a lifting ring that pivots 180° front to back and a base that swivels 360° to compensate for pitch, roll, and sway when lifting heavy or unbalanced loads. A black oxide finish gives these hoist rings mild corrosion resistance.
Install the base of these hoist rings flush to your mounting surface.
Note: Capacities listed are for vertical lifting only. As the lift angle changes from vertical, the amount of weight the hoist ring can lift is significantly reduced. For example, when lifting a 1,000 lb. load at a 45° angle, you must choose a hoist ring with a capacity of at least 1,400 lbs. Do not use at an angle less than 30°.
Warning: Never use to lift people or items over people.
For technical drawings and 3-D models, click on a part number.
Rings | Replacement Bolt Kits | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Thread Size | Thread Lg. | Inside Wd. | Overall Ht. | Vertical Capacity, lbs. | Tension Indicated, ft.-lbs. | Indicator Temperature Range, °F | Movement | Specifications Met | Each | Each | ||
Black-Oxide Steel with Zinc-Plated Steel Bolt | ||||||||||||
| 1 1/4"-7 | 1 7/8" | 3 1/2" | 10 5/8" | 15,000 | 470 | 0° to 165° | 180° Pivot and 360° Swivel | ASME B30.26, CE Marked | 0000000 | 0000000 | 0000000 | 0000000 |
Unthreaded Stub-to-Stub Turnbuckles—Not for Lifting
Weld these stubs to parts or use to push objects apart instead of pulling them together.
Galvanized steel has a thick coating for mild corrosion resistance.
Forged bodies and components are stronger than cast bodies and components.
Note: Capacities listed are for straight or in-line pull only.
For technical drawings and 3-D models, click on a part number.
Stub | ||||||||
|---|---|---|---|---|---|---|---|---|
| Capacity, lbs. | Retracted Lg. | Max. Adjustment | Extended Lg. | Dia. | Lg. | Thread Size | Each | |
| 14,800 | 20" | 6" | 26" | 1 1/4" | 4 1/2" | 1 1/4"-7 | 00000000 | 000000 |
Clevis-to-Clevis Turnbuckles—For Lifting
Made of galvanized steel, these turnbuckles have a thick coating for mild corrosion resistance.
Note: Capacities listed are for vertical lift only.
For technical drawings and 3-D models, click on a part number.
Turnbuckles | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Clevis Pin | Jam Nuts | |||||||||||
| Capacity, lbs. | Retracted Lg. | Max. Adjustment | Extended Lg. | Dia. | Closure Type | Clevis Inside Wd. | Thread Size | Specifications Met | Each | Each | ||
Forged Galvanized Steel Body with Forged Galvanized Steel Fittings | ||||||||||||
| 15,200 | 31 1/2" | 12" | 43 1/2" | 1 1/8" | Cotter Pin | 1 27/32" | 1 1/4"-7 | ASME B30.26, ASTM F1145 Type 1 | 0000000 | 0000000 | 000000000 | 000000 |
| 15,200 | 37 1/2" | 18" | 55 1/2" | 1 1/8" | Cotter Pin | 1 27/32" | 1 1/4"-7 | ASME B30.26, ASTM F1145 Type 1 | 0000000 | 000000 | 000000000 | 00000 |
| 15,200 | 44 1/4" | 24" | 68 1/4" | 1 1/8" | Cotter Pin | 1 27/32" | 1 1/4"-7 | ASME B30.26, ASTM F1145 Type 1 | 0000000 | 000000 | 000000000 | 00000 |
Clevis-to-Eye Turnbuckles—For Lifting
Made of galvanized steel, these turnbuckles have a thick coating for mild corrosion resistance.
Note: Capacities listed are for vertical lifting only.
For technical drawings and 3-D models, click on a part number.
Turnbuckles | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Clevis Pin | Jam Nuts | |||||||||||||
| Capacity, lbs. | Retracted Lg. | Max. Adjustment | Extended Lg. | Dia. | Closure Type | Clevis Inside Wd. | Eye Shape | Eye ID | Thread Size | Specifications Met | Each | Each | ||
Forged Galvanized Steel Body with Galvanized Steel Fittings | ||||||||||||||
| 15,200 | 32" | 12" | 44" | 1 1/8" | Cotter Pin | 1 27/32" | Oval | 1 13/16" | 1 1/4"-7 | ASME B30.26; ASTM F1145 Type 1 | 0000000 | 0000000 | 000000000 | 000000 |
| 15,200 | 38" | 18" | 56" | 1 1/8" | Cotter Pin | 1 27/32" | Oval | 1 13/16" | 1 1/4"-7 | ASME B30.26; ASTM F1145 Type 1 | 0000000 | 000000 | 000000000 | 00000 |
| 15,200 | 44 1/2" | 24" | 68 1/2" | 1 1/8" | Cotter Pin | 1 27/32" | Oval | 1 13/16" | 1 1/4"-7 | ASME B30.26; ASTM F1145 Type 1 | 0000000 | 000000 | 000000000 | 00000 |
Threaded Stud-to-Stud Turnbuckles—Not for Lifting
Galvanized steel has a thick coating for mild corrosion resistance.
Note: Capacities listed are for straight or in-line pull only.
For technical drawings and 3-D models, click on a part number.
| Capacity, lbs. | Retracted Lg. | Max. Adjustment | Extended Lg. | Retracted Stud Lg. | Thread Size | Each | |
| 14,800 | 20" | 6" | 26" | 4 1/2" | 1 1/4"-7 | 00000000 | 000000 |