We will reply to your message within an hour.
These steel anchors are available with corrosion-resistant finishes.
These 18-8 stainless steel anchors have good chemical resistance.
More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.
Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose.
A zinc plating provides corrosion resistance in wet environments.
The removable flat head provides a flush finish in countersunk holes.
Drive these tools with a hammer until the thicker portion of the tool makes contact with the anchor, causing it to expand.
These 316 stainless steel anchors have excellent resistance to chemicals and salt water.
Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.
Also known as caulk-in anchors, these stay secure when there's not much material to hold.
Drive these tools with a hammer to expand anchors.
An adjustable stop allows you to set anchors at consistent depths. Use with a hammer.
The fastest way to install shallow-hole female-threaded anchors. Just push the tip of the tool into the anchor and turn the tool with a power drill.
Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.
Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.
Use in applications requiring high strength.
For narrow holes and small cavities where toggle anchors won't fit.
These stud-style anchors include a nut and a washer.
A drilled hole is required for installation.
High-strength toggle anchors provide an extremely strong hold and stay in position when a bolt is removed.
A spring-loaded toggle holds against the back of the material.
Bolts are beveled under the head for use in countersunk holes.
The spring holds the washer and toggle against opposite sides of the wall, so everything's in position before you begin tightening. Once tightened, the spring adds vibration resistance.
These hangers are a popular choice for overhead applications.
You can use these versatile hangers in a threaded hole (as you would a screw), or secure them with a nut (as you would a bolt).
These hangers have internal threads for use with threaded rods, bolts, and anchors.
About half the strength of medium-strength bolts, these bolts are for light duty work-holding.
18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.
These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.
These clamps rotate 360° and pivot 45° to ensure the rod hangs straight, even on sloped beams.
Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.
A toothed clip secures these clamps to the beam—no fasteners required.
Install directly into a mounting surface to suspend threaded rod from ceilings and walls.
Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.
Add an eye nut to threaded rod to hang the rod from rings, hooks, and hangers.
Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.
Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.
Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.
Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.
A mounting plate provides a more secure hold at the mounting surface.
Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.
Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.
A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to disassemble it.
Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.
Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.
Temporarily mount routing rings and other threaded components to steel and iron surfaces.
Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.
Wind rope around these cleats for a secure hold.
Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back to compensate for roll and sway when lifting heavy or unbalanced loads.
Keep on hand all the parts needed to assemble custom hoist rings.
With three different thread sizes, these hoist rings are useful when you need to lift different types of equipment.
Also known as nut eyebolts, these are designed for through-hole applications.
Use these eyebolts for routing wire and for other light duty applications.
Install these stud-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.
Also known as socket-end swage fittings, install these stud-end fittings with a roller swage press for a strong, permanent hold.
A black-oxide finish provides mild corrosion resistance.
These stainless steel anchor studs offer excellent corrosion resistance.
Threads on one end make it easy to screw these hooks directly into a wall.
The closed body protects threads from damage and debris and has a slim profile to fit in tight spaces.
For use with wire rope in light duty applications, these turnbuckles have a closed body that protects threads from damage and debris.
Weld these stubs to parts or use them to push objects apart instead of pulling them together.