These steel anchors are available with corrosion-resistant finishes.

More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

A zinc plating provides corrosion resistance in wet environments.

A zinc plating provides corrosion resistance in wet environments.

More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

A zinc plating provides corrosion resistance in wet environments.

Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.

Drive these tools with a hammer to expand anchors.

The fastest way to install shallow-hole female-threaded anchors. Just push the tip of the tool into the anchor and turn the tool with a power drill.

Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.

Bolts are beveled under the head for a flush finish in countersunk holes.

For narrow holes and small cavities where toggle anchors won't fit.

These stud-style anchors include a nut and a washer.

18-8 stainless steel anchors have good chemical resistance.

18-8 stainless steel anchors have good chemical resistance.

A spring-loaded toggle holds against the back of the material.

You can use these versatile hangers in a threaded hole (as you would a screw), or secure them with a nut (as you would a bolt).

18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

These clamps rotate 360° and pivot 45° to ensure the rod hangs straight, even on sloped beams.

A toothed clip secures these clamps to the beam—no fasteners required.

For centered load distribution, these clamps grip both sides of the beam and hang threaded rod from the middle.

Install directly into a mounting surface to suspend threaded rod from ceilings and walls.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

Suspend and route flat-bottomed objects such as strut channel and small duct.

These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.

Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back to compensate for roll and sway when lifting heavy or unbalanced loads.

Choose these hoist rings when you need to lift your load from the side.

Keep on hand all the parts needed to assemble custom hoist rings.

Also known as nut eyebolts, these are designed for through-hole applications.

A black-oxide finish provides mild corrosion resistance.

These stainless steel anchor studs offer excellent corrosion resistance.