Also known as high-inrush current switches, these switches can handle starting currents up to 10 times greater than their current rating, such as when a motor starts. They're often used with amplifiers, power supplies, and other high-starting-current devices.

Switches with an on-on position designation alternate power between sets of terminals.

Switches with a guard prevent accidental activation.

For technical drawings and 3-D models, click on a part number.

Rated IP67 for protection from dust and temporary submersion. Also known as high-inrush current switches, these switches can handle starting currents up to 10 times greater than their current rating, such as when a motor starts. They're often used with amplifiers, power supplies, and other high-starting-current devices.

For technical drawings and 3-D models, click on a part number.

Able to withstand high currents, these switches are often used with motors and pumps.

Switches with an on-on position designation alternate power between sets of terminals.

For technical drawings and 3-D models, click on a part number.

Maximize space in a panel—these switches are smaller than most standard rocker switches.

Note: Illuminated switches include a bulb. If wiring the switch and the bulb to the same circuit, the circuit voltage must not exceed bulb voltage.

Switches with an on-on position designation alternate power between sets of terminals.

For technical drawings and 3-D models, click on a part number.

For switches with wire leads, the front and rear panel seals meet IP67.

For switches with quick-disconnect terminals and screw terminals, the front panel seals meet IP67 and the rear panel seals meet IP60.

Switches with maintained/momentary switch action stay switched from one side and spring back from the other side.

Switches with an on-on position designation alternate power between sets of terminals.

For technical drawings and 3-D models, click on a part number.

Instead of hardwiring power supplies, appliances, and other electronic devices, these connectors let you plug in an IEC power cord and turn the power on and off without needing a separate switch. Wire these connectors using the quick-disconnect terminals; they slide together with matching terminals on your wiring for a secure hold that's also easy to pull apart to make repairs. The terminals are on the back of the connector, so the wiring stays inside your device.

Rated IP40, these connectors prevent objects larger than a 1 mm-wd. wire from touching internal components and accidentally shocking you. With Class I shock protection, they’re insulated and have a protective ground. Some have a fuse drawer to hold a fuse, which prevents short circuits and circuit overloads from damaging your device. The fuses are sold separately.

These connectors meet UL 94 V-0, which means they self-extinguish within 10 seconds if they catch fire, and won’t spread the fire by dripping. They’re also UL and C-UL recognized components, CE and ENEC marked, and CSA certified, so they meet stringent safety standards.

Screw-on connectors mount to housings of any thickness, as long as you can drill mounting holes into them. Snap-in connectors have tabs on the side to mount to housings without using fasteners. But, they require a specific panel thickness and precisely cut hole for secure mounting.

Connectors with an indicator light on their switch show if your device is powered on.

Shielded connectors protect against interference from nearby equipment.

For technical drawings and 3-D models, click on a part number.

Rated IP67, these connectors create a dust- and watertight seal where they fit into the housing of power supplies, appliances, and other electronic devices. Instead of hardwiring your devices, these connectors let you plug in a standard IEC power cord and turn the power on and off with a built-in switch. Wire these connectors using the quick-disconnect terminals; they slide together with matching terminals on your wiring for a secure hold that's also easy to pull apart to make repairs. The terminals are on the back of the connector, so the wiring stays inside your device.

To protect your devices, these connectors have a thermal circuit breaker that uses the excess heat when there’s overcurrent to trip the breaker and cut power. If there’s a short circuit, the breakers can safely stop up to a 2,000-Amp breakthrough current. These connectors also have Class I shock protection, so they’re insulated and have a protective ground.

These connectors meet UL 94 V-0, which means they self-extinguish within 10 seconds if they catch fire, and won’t spread the fire by dripping. They’re also UL and C-UL recognized components, and CE and ENEC marked, so they meet stringent safety standards.

For technical drawings and 3-D models, click on a part number.