Attach cutoff wheels, grinding wheels, and other abrasive wheels to hand-held drills and die grinders.

Mount wheel brushes that have an arbor hole to hand-held drills and die grinders.

Reduce the arbor hole size on a wheel brush so that it fits the shaft on your tool.

The arbor’s shank attaches to hand-held drills and die grinders. Threads on the body hold the sanding roll in place.

Use flap wheels with a threaded stud in tools that accept a shank.

Attach flap wheels with an arbor hole to tools that accept a shank.

Also known as cross- and square-sanding pad shank adapters, these arbors are required to attach sanding pads for internal and irregular surfaces to hand-held drills and die grinders.

Mount cutoff wheels, grinding wheels, and other abrasive discs to the straight shaft on bench-top motors, grinders, and buffers.

Secure the shank into the collet or chuck of your tool. Attach the quick-change fastener on the sanding disc to the corresponding fastener on the backup pad.

Thread these pads onto the tool’s arbor.

Secure the shank into the collet or chuck of a tool.

Holes allow dust removal when used with a vacuum sander.

Thread the stud into the tool's spindle and then press the sanding disc onto the backup pad.

These pads are designed to channel air flow to the sanding disc for cooler operation, prolonging the life of the disc.

Slide a sanding sleeve on the drum and tighten the nut or screw to securely hold the sleeve.

This drum is required to use a sanding sleeve with a Dremel grinder.

Mount a sanding sleeve to the straight shaft of a bench or pedestal grinder using one of these drums.

Attach to grinder and buffer shafts to hold buffing wheels with shanks.

Use one of these spindles to mount buffing wheels to the tapered shaft on your grinder or buffer.

Keep a convenient mix of spiral-wound sanding rolls on hand. As the outer layer wears away, new abrasive is exposed.

The premium abrasive stays sharp longer.

These arbors are designed to absorb vibration.

Each of these sets comes with three differently sized arbors.

Mount these arbors into manual milling machines that have an R8 taper spindle.

The Morse taper end fits into a machine spindle and the Jacobs taper end is compatible with a Jacobs taper drill chuck.

One end is made of soft steel that can be machined to an exact size and shape; the other end is a Morse taper that fits into a machine spindle.

If your Morse taper arbor is too small or large for your machine spindle, insert it into one of these adapters. Also known as sleeves or shell sockets.

Insert your Morse taper arbor into one of these extensions to get additional reach.

For better control when drilling small holes with a drill press or milling machine, the attachment on these arbors lets you apply light feed pressure with your fingers while the machine rotates the bit.

Drill extremely small holes with a drill press using these adapters. The shank fits into a collet or adjustable drill chuck, and the other end securely holds a wire gauge drill bit.

Switch hole saws without using adapters or special tools.

These arbor adapters are required when using Milwaukee hollow-core cutters. Also known as annular cutters.

Securely grip end mills in machines with a CAT 40 taper spindle.

Convert tools with a Morse taper shank to an R8 shank for use in manual milling machines that have an R8 taper spindle.

Hold collets in the spindle of a milling machine.

After installing the R8 body in the milling machine spindle, tool holders can be switched out in seconds.

An expanding screw widens the end of the mandrel for a tight hold on the inside of a workpiece.

The sleeve on these mandrels expands to hold a range of diameters for better versatility than solid and expanding-end mandrels.

A hardened body and point provide the extra strength and wear resistance necessary for continuous use on manual or CNC lathes.

Also known as bull-nose centers, these have a wide head to hold pipe and large-diameter tubing.