Spring pressure ensures a constant flow of grease.

Turn the metering pin to adjust flow rate.

Don’t wait for grease to travel through a new service line—install this grease-filled tubing between the pump and a lubrication point to begin lubricating immediately.

This dispenser delivers over three times more grease per stroke than our dual-output dispensers.

Dispense grease using compressed air.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings.

Use compressed air to dispense grease.

These guns deliver twice as much grease per stroke than standard lever-grip guns.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Dispensing more grease per pump than pistol-grip guns, lever-grip guns are better for applications that require high grease output.

Designed to lubricate linear motion components, such as slide bearings, guides, and ball screws, these guns work exclusively with THK grease cartridges and fittings.

Turn a small tube of grease into a dispenser.

Because of their one-hand operation, pistol-grip grease guns are easier to use for adding grease to hard-to-reach places than lever-grip guns.

More portable than air-powered options, these guns operate on a rechargeable battery.

Thread these dispensers directly into bearing housings, pumps, and other machinery. Flip the lever to start and stop flow; turn the dial to adjust flow.

A sealed design prevents contamination in dirty and dusty environments.

Serve multiple lubrication points from a single location.

Control the flow of oil to a single lubrication point.

Manually adjust the flow of oil to a single lubrication point.

For use in clean environments, these manifolds have multiple air vents that keep pressure balanced.

Use this dispenser to brush oil on chain, gears, and conveyors. Often used to replenish lubricant after washdowns.

Connect these brushes to oil reservoirs and flow adjustment valves to lubricate chain, gears, and conveyors.

A solenoid automatically starts and stops flow to dispense lubricant while equipment is running.

Use these brushes to lubricate chain, gears, and conveyors. Connect to an oil dispenser, then turn the dial to adjust flow.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

Use with manual and electric pumps to dispense different amounts of oil from multiple lubrication points.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

Pull the trigger on these oilers for easier one-hand operation than standard hand-held oil dispensers.

Deliver a mist of oil using shop air.

The color-coded threads and numerical markings on these valves ensure consistent and repeatable settings. One full revolution of the handle reveals a new color to indicate the set point. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Designed for high-pressure instrumentation applications, these valves are rated for up to 10,000 psi and have a hex nut and threads below the handle for panel mounting. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Rated for nearly twice the maximum temperature of standard threaded precision flow-adjustment valves, these can handle up to 700° F. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To ensure highly precise flow adjustment, these valves adjust flow in smaller increments than other valves for finer control over the flow rate in metering and sampling applications. Use them with water, oil, air, and inert gas.

Often used in hydraulic and compressed air systems, these valves can withstand at least 6,000 psi. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a low-profile body and a narrow port-to-port length, these valves fit in tight spots. Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a PTFE seal and a PVDF body. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

These valves press down on the outside of tubing to adjust flow without contacting the process media.

Also known as proportional V-ball valves, these have a motor that adjusts and regulates flow in applications with higher flow rates and pressures than solenoid valves. As you increase the intensity of the electrical signal, the motor opens the valve, moving a ball with a V-cut opening that proportionately allows more flow as the valve opens. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

Valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

Plastic provides a lightweight and corrosion-resistant alternative to metal. Use with oil. These valves gradually open and close to adjust and regulate flow.

Attach garden hose to the valve outlet. Use with water. These valves gradually open and close to adjust and regulate flow.

Insert unthreaded pipe into the socket ends and weld to create a permanent, leak-tight connection. These valves are for use with water, oil, air, inert gas, and steam. They gradually open and close to adjust and regulate flow.

An aluminum body provides strength and durability at half the weight of other metal flanged flow-adjustment valves. These valves are for use with water, oil, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Metal provides more durability than plastic. With seats that can stand up to aggressive and corrosive solutions, these valves are often used in chemical-processing applications. They bolt to flanges to adjust and regulate flow in flanged pipelines.