Suitable for general purpose use.

Turn the knob to adjust how much these valves will open or close when actuated. They are often used in irrigation and landscaping applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Control flow in high-pressure lines in tight spots—these valves have the highest pressure ratings of our compact valves.

These valves are rated for use in hazardous locations with flammable gas and combustible dust.

To fit in tight spots, these valves have a slimmer body than standard valves with an exhaust port.

To change the flow rate of antifreeze and cleaning solutions, use the adjustment screw or knob to manually set how much these valves will open when actuated.

A built-in strainer traps debris and allows you to replace the screen without disconnecting your pipeline.

Use with coolant and detergent such as ethylene glycol or soap solutions.

With a plastic body and a fluoroelastomer seal, these valves can stand up to aggressive and corrosive solutions in chemical-processing applications.

For applications sensitive to contamination, these valves stop flow without contacting the process media by pressing down on the outside of tubing.

To fit in tight spots, these valves are lower profile and available in smaller connection sizes than standard valves for natural gas, propane, and butane.

These valves have threaded NPT connections.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

For use in general purpose applications with water, oil, and inert gas.

Limit wear and damage in high-cycling applications—these valves have additional seals that prevent leakage to reduce maintenance time.

Less than half the height of standard severe-duty valves, these fit in small spaces and low-clearance pipelines.

About half the height of our other versa-mount valves, these fit in tight spots.

With a ball-valve design, these valves can handle three times the flow of butterfly valves.

Also known as piston valves, these have a compact, lightweight actuator that allows them to be installed in any mounting orientation. They’re often used in water-treatment applications.

For food and beverage applications that require frequent cleaning, these valves have quick-clamp connections, polished internal surfaces, and a three-piece bolted body for easy disassembly.

For general purpose applications with water, oil, and inert gas.

Maintain and repair these valves without unthreading pipe connections. They have a three-piece bolted body that disassembles inline for access to internal components.

Their ball valve design allows these valves to handle three times the flow of butterfly valves.

For three times the flow of butterfly valves, these have a ball valve design.

Insert unthreaded pipe into the socket ends and bond with PVC primer and cement to create a permanent, leak-tight connection.

Repair actuated on/off valves from Asco, Burkert, Granzow, and Parker with these kits that include replacement seals, plunger assemblies, and springs.

Often used for chemical analysis and other laboratory testing, these valves have a PTFE seal and body to withstand aggressive and corrosive solutions. They operate on electricity to automatically divert flow between ports.

Set the electronic timer on these drain valves to open automatically at your specified time interval.

Use the digital display to set these valves to open automatically at precise intervals.

Sized right for tight spots.

Able to withstand up to 400 psi, these have the highest pressure rating of all our float-operated drain valves.

When your compressor turns off, it creates back pressure that opens these valves automatically, allowing liquid to escape.

These valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

Often used to extend and then retract a cylinder at different speeds, these valves create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as 5/2 valves, they actuate when voltage is applied to the electrical connection.

In the off position, these valves exhaust all air pressure, allowing the equipment to return to the neutral position. Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Apply voltage to the electrical connection to actuate.

These valves create one action, such as extending a cylinder. Apply voltage to the electrical connection to actuate. They're also known as 3/2 valves.

Also known as 3/3 valves, these valves close all ports in the off position to stop equipment in a locked position with air pressure holding it in place. They're often used for vacuum suction and release applications and intermediate cylinder stops.

Ceramic plates form a longer-lasting seal against oil and dust than rubber seals that deteriorate over time. These valves withstand use in corrosive, dusty, and dirty environments such as foundries, paper mills, and steel plants. Apply voltage to the electrical connection to actuate.

Use a single valve to create motion and control the speed of that motion.

Often used to extend and then retract a cylinder at different speeds, they create two actions and have two exhaust ports, which allows you to control the speed of each action by attaching a flow control valve to each exhaust port. Also known as pilot valves and 4-way valves, they use an air signal to actuate, so they're good for environments where electrical use may be dangerous.

Mix and match valve styles on one manifold to meet your control needs. Mount multiple valves to a manifold to reduce piping requirements and create multiple actions from a single pressure input.

With two 2-way integrated solenoid valves, these electrically controlled valves direct airflow to venturi pumps, which generate the suction you need to run end-of-arm tools, such as vacuum cups.

Also known as solenoid valves, these valves are operated by an electrical signal to turn airflow on or off.

Designed for use in dust-collection systems, these diaphragm valves periodically burst air to knock debris from filters.

Often used in wet conditions and harsh environments, these valves have a 316 stainless steel body for excellent corrosion resistance.

For a longer service life than brass and cast iron valves, these have a durable bronze body.

To maintain contaminant-free standards in clean room environments, these valves come cleaned and bagged to Class 100 clean room standards and have a 316 stainless steel body with a smooth finish to resist dust collection.

Use this valve in light duty water systems with garden hose thread (GHT) connections.

Hook up these valves to equipment with garden hose thread (GHT) connections.

Valves have a brass body and NPT connections.

Change outlet pressure without using a gauge—turn the dial to adjust the outlet pressure in 10 psi increments.

Often used for oxygen service and other high-purity applications, these valves are cleaned and bagged to meet CGA G-4.1 standards to prevent contamination.

Withstand more than six times the inlet pressure of standard pressure-regulating valves.

Valves have a brass body.

Flowmeters let you see the gas flow rate from a distance.

Maintain contaminant-free standards in clean room environments. These valves come cleaned and bagged to Class 100 clean room standards and have a 316 stainless steel body with a smooth finish to resist dust collection.

For easy panel mounting in your water system, these valves have threads below the adjustment knob and come with a panel-mount nut.

Often used for pressure-vessel testing and other high-pressure applications, these valves can handle at least seven times the outlet pressure of standard tank-mount pressure-regulating valves.

A 316 stainless steel body provides exceptional corrosion resistance in wet conditions and harsh environments.

For a longer service life than cast iron valves, these have a durable bronze body.

Body is cast iron.

For a longer service life than standard valves for cryogenic liquids, these have a durable bronze body. They’re for use with liquid argon, liquid carbon dioxide, liquid nitrogen, and liquid oxygen.

Choose from valves for liquid argon, liquid nitrogen, liquid carbon dioxide, or liquid oxygen.

Install these valves directly in gas distribution pipelines.

For use with acetylene, hydrogen, methane, propane, or propylene gas.

Valves have NPT connections.

For touch-free flushing on your toilets or urinals, attach these converters to your manual flush valves. They're activated by a motion sensor but also have a manual override option.