A small hex size makes these high-flow mufflers a great fit for cramped spaces.

In addition to a filter, these mufflers have a wool felt disc to trap oil mist.

With a threaded connection on both ends, these mufflers can be installed anywhere in your line.

These mufflers can be cleaned for an extended service life.

Also known as reclassifiers, these mufflers have a clear reservoir with a drain plug to remove and store oil mist for reuse.

Suitable for use with welding equipment, these mufflers are made of flame-resistant materials. They reduce noise by 35 dB.

Don’t let an unexpected clog interrupt your work. These mufflers have a filter that slides up slowly as it clogs to indicate when the muffler should be replaced. They reduce noise by 30-35 dBA

Clean the air going into small blowers and air-powered equipment in tight spaces.

Purify exhaust fumes while silencing the noise from your oil-free high-vacuum pumps.

Made of FDA listed materials, these rigid bellows are suitable for food and beverage applications.

Add cuff inserts to these flexible bellows for a custom fit.

Sewn seams let these bellows breathe, so they retract quickly in fast-cycling applications.

These fiberglass bellows withstand temperatures up to 450° F—about twice as much as standard breathable round bellows with flange ends. They also protect against flames and sparks.

Attach the cuff end with a hose clamp and screw mount the flange end.

Slide these bellows over square rods and shafts.

Secure the cuff ends with hose clamps.

Made of coiled spring steel, these bellows protect equipment from hot and sharp chips.

A honeycomb core is bonded between two aluminum sheets for rigidity.

This synthetic felt is an economical alternative to wool felt.

Line toolboxes and drawers to cushion and protect small parts.

Made of 100% wool, this is the hardest felt we offer, yet it can still be used for polishing. It is more abrasion resistant and better at damping vibration than other felt. Includes S2-32, S2-24, and S2-20 felt grades.

With an aramid honeycomb core sandwiched between carbon fiber or fiberglass for rigidity, these panels are strong, but lightweight, and won’t conduct heat. Often used as wall panels in structural and insulating applications, they’re a lightweight alternative to solid composite and aluminum honeycomb panels.

Add stiffness to composite sandwiches without adding a lot of weight.

The best sound absorbers of all our rigid sheets, use to quiet noisy areas in your facility. They're peaked on one side for more sound-absorbing area than flat sheets. Made of melamine, they have an acrylic resin finish that resists dust and dirt and wipes clean.

These polypropylene foam sheets will not degrade if exposed to moisture and occasional salt water spray. Use them to quiet noisy areas and line machine enclosures.

Also known as egg crate, these sheets have peaks and valleys that absorb more sound at higher frequencies than flat-surface sheets. Use them to quiet noisy areas and line machine enclosures. Sheets are made of humidity-resistant polyurethane foam.

This insulation meets ASTM E162 for flame retardance and ASTM E662 for smoke output. Use to quiet noisy areas and line machine enclosures. Sheets are made of polyimide foam.

The foil facing reflects heat. Use these sheets to quiet noisy areas and line machine enclosures. They’re made of humidity-resistant polyurethane foam.

Apply these coatings to irregular shapes and large areas and reduce noise caused by vibration. Keep applying coats until desired noise reduction is achieved.

Set up these free-standing partitions to reflect sound and block noise from traveling to other parts of your facility. A vinyl barrier is sandwiched between two vinyl-coated fiberglass absorbers.

Choose the pressure range you need. When these valves receive an air signal, they quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. They're often used with air compressors that require continuous operation. Also known as quick exhaust valves.

Control the flow of exhaust air while also regulating the exhaust air speed. These valves dump exhaust air to the atmosphere without routing it back through a directional control valve. The 90° elbow shape allows you to install them in tight spaces. Also known as quick exhaust valves.

Quiet squeaky floor joists and reduce vibration with this foam tape.

Reduce rattles and squeaks between parts with this abrasionresistant flocked tape. The acrylic adhesive sticks even on hard-to-bond plastics.