Joint Type Joint Type | Show |
|---|
 | Ball and Socket |
Joint Type Joint Type | Hide |
|---|
 |  |
| Pin and Block | Needle Bearing |
|  |
| Ball and Socket | Spring |
 | |
| Geared |
System of Measurement System of Measurement |
|---|
|
Shaft Mount Type Shaft Mount Type |
|---|
 |  |
| Spring Pin | Set Screw |
Material Material |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
Maximum Torque Maximum Torque |
|---|
|
|
Torque Torque |
|---|
|
Ball Material Ball Material |
|---|
|
Maximum Operating Angle Maximum Operating Angle |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Number of Set Screws Required Number of SetScrews Required |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
About U-Joints (Universal Joints)
U-joints are used to connect two shafts that have a high amount of misalignment.
More
Corrosion-Resistant Precision Single U-Joints
Stainless steel U-joints are more corrosion resistant than steel U-joints. They allow for zero backlash (no play) and are good for applications requiring consistent motion and precise control.
To connect set screw mount U-joint, tighten a set screw at each end. To connect spring-pin mount U-joints, drill a hole through the joint and shaft and insert a spring pin (not included).
For technical drawings and 3-D models, click on a part number.
For Shaft | Torque | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Dp. | Joint Dia. | O'all Lg. | Max. Operating Angle | Max. Speed | Max. Torque, in.-lbs. | 5° Operating Angle | 10° Operating Angle | Joint Type | Shaft Mount Type | No. of Set Screws Required | For Set Screw Thread Size | Each | |
303 Stainless Steel | ||||||||||||||
| 3/32" | 11/32" | 3/16" | 1" | 30° | Not Rated | 1 | 0.9 in.-lbs. @ 1,500 rpm | 0.8 in.-lbs. @ 1,500 rpm | Ball and Socket | Spring Pin | __ | __ | 00000000 | 000000 |
| 1/8" | 3/16" | 3/16" | 1" | 30° | Not Rated | 1 | 0.9 in.-lbs. @ 1,500 rpm | 0.8 in.-lbs. @ 1,500 rpm | Ball and Socket | Spring Pin | __ | __ | 00000000 | 00000 |
| 3/16" | 7/16" | 9/32" | 1 3/8" | 30° | Not Rated | 4 | 3.6 in.-lbs. @ 1,500 rpm | 3.2 in.-lbs. @ 1,500 rpm | Ball and Socket | Spring Pin | __ | __ | 00000000 | 00000 |
| 1/4" | 1/2" | 3/8" | 1 3/4" | 30° | Not Rated | 16 | 14.4 in.-lbs. @ 1,500 rpm | 12.8 in.-lbs. @ 1,500 rpm | Ball and Socket | Set Screw | 2 | 6-32 | 00000000 | 00000 |
Precision Single U-Joints
These U-joints are good for applications requiring consistent motion and precise control. Use the included spring pins to connect.
For technical drawings and 3-D models, click on a part number.
Precision Double U-Joints
Allowing for zero backlash (no play), this U-joint is good for applications requiring consistent motion and precise control. Joint is corrosion-resistant stainless steel. Tighten the set screws to connect.
For technical drawings and 3-D models, click on a part number.
For Shaft | Torque | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Dp. | Joint Dia. | O'all Lg. | Max. Operating Angle | Max. Speed | Max. Torque, in.-lbs. | 5° Operating Angle | 10° Operating Angle | Parallel Misalignment Capability | Joint Type | No. of Set Screws Required | For Set Screw Thread Size | Each | |
303 Stainless Steel | ||||||||||||||
| 1/4" | 1/2" | 3/8" | 2 1/2" | 30° | Not Rated | 16 | 14.4 in.-lbs. @ 1,500 rpm | 12.8 in.-lbs. @ 1,500 rpm | 0.45" | Ball and Socket | 2 | 6-32 | 00000000 | 0000000 |
Adjustable-Length Precision Double U-Joints
Adjust the length of this U-joint from 2 3/4" to 3” to fit your application. It allows for zero backlash (no play) and is good for applications requiring consistent motion and precise control. Joint is stainless steel for good corrosion resistance. To connect, drill a hole through the joint and shaft and insert a spring pin (not included).
For technical drawings and 3-D models, click on a part number.
For Shaft | Torque | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Dp. | Joint Dia. | O'all Lg. | Max. Operating Angle | Max. Speed | Max. Torque, in.-lbs. | 5° Operating Angle | 10° Operating Angle | Parallel Misalignment Capability | Joint Type | Each | |
303 Stainless Steel | ||||||||||||
| 1/4" | 3/8" | 3/8" | 2 3/4"-3" | 30° | Not Rated | 16 | 14.4 in.-lbs. @ 1,500 rpm | 12.8 in.-lbs. @ 1,500 rpm | 0.7" | Ball and Socket | 00000000 | 0000000 |