The flanged housing makes these bearings a good solution for vertical linear motion applications.

Use the adjustment screw in the housing to tighten or loosen the snugness (also known as preload) of the bearing to your shaft.

Designed to handle heavy loads, these bearings have the highest load capacities of any mounted linear ball bearings we offer.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard mounted linear ball bearings for Support Rail Shafts.

A flanged housing with mounting holes connects these bearings directly to your system. They have a grooved inner diameter that's designed to work with spline shafts. Together, they transmit rotary power while allowing the bearing to move freely along the length of the shaft.

Use ball bearings in debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings.

Ball bearings create less friction than sleeve bearings, so they require less force to operate.

With a grooved inner diameter, these bearings are designed to work with splined shafts. Together, they transmit rotary power while allowing the bearing to move freely along the length of the shaft. All are for use where shaft misalignment is unlikely.

These carriages and guide rails are steel.

These carriages and guide rails are steel.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

With a plastic cage that surrounds the ball bearings to prevent them from colliding, these extra-wide carriages run quietly for many cycles without needing maintenance. All of these carriages have a wide base and low-profile design to stabilize moment (twisting) and off-center loads better than other carriages.

Mount to vertical surfaces for applications where tight tolerances aren't required.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

Use these carriages and guide rails for light loads where precise movement is not required.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

Slides have a row of ball bearings on each side of the rail.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Connect to an electric motor with the included NEMA mounting flange.

A micrometer handle ensures accurate, repeatable positioning along a single axis—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

The stacked design provides stability for deep and wide drawers.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

With fewer moving parts than other lock-open drawer slides, these collect less debris for a longer service life.

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

A lever locks the drawer in the open as well as closed position; push the lever to release the lock.

These slides gradually slow the drawer's motion to prevent it from slamming open.

Mounting to the tops and bottoms of drawers, these steel slides support drawers even if they’re tall and hold heavy equipment.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Position shafts an inch or two off the ground to maintain bearing and part clearance. Support rails provide stability over the entire length of shaft, allowing virtually unlimited travel lengths and eliminating bending under moderate to heavy loads.

At approximately one-third the height of standard versions, these rails provide linear shaft support in applications with low vertical clearance. They provide stability over the entire length of shaft, allow virtually unlimited travel lengths, and eliminate bending under moderate to heavy loads.

Loosen the clamping screw to install, then tighten to secure. Made of lightweight, corrosion-resistant aluminum, these shaft supports hold linear shafts perpendicular to the mounting surface. Use with light to medium loads where shaft alignment is not critical.

Slide the shaft in to install, then tighten to secure. For use with light to medium loads where shaft alignment is not critical, these shaft supports brace the end of a linear shaft along the ground or other flat surface.