Used in food, beverage, pharmaceutical, and chemical plants, these mounted ball bearings are IP69K certified for washdown environments and have a two-bolt flange for mounting. Their 316 stainless steel housing has excellent corrosion resistance and prevents rust caused by salt water, chlorine solutions, and chemicals. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings grip shafts as you tighten their screw. They don’t use a collar, but the screw leaves some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it secures against the inner ring.

Snap optional covers onto bearings to protect them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange. For excellent corrosion resistance and preventing rust caused by salt water, chlorine solutions, and chemicals, their housing is made of 316 stainless steel. All have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw shaft-mount bearings secure to shafts when you tighten the set screw, with no need for an additional collar. Set screws cause some amount of marring on shafts.

Concentric lock bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. Install them by tightening the locking collar’s screw until it presses against the inner ring.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

The lubricant in these mounted ball bearings is suitable for incidental contact with food. Bearings are self-aligning to compensate for shaft misalignment.

Steel bearings are stronger than stainless steel bearings, but not as corrosion resistant.

Stainless steel bearings are more corrosion resistant than steel bearings.

Sealed bearings block out dust and other contaminants better than shielded bearings.

Shielded bearings dissipate heat more efficiently than sealed bearings.

For technical drawings and 3-D models, click on a part number.

Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. They have excellent corrosion resistance and prevent rusting caused by salt water, chlorine solutions, and chemicals because their housing is 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it grips the inner ring.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. All have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

316 stainless steel bearings resist corrosion and prevent rusting caused by salt water, chlorine solutions, and chemicals. Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it grips the inner ring.

For technical drawings and 3-D models, click on a part number.

The lubricant in these mounted ball bearings is suitable for incidental contact with food. Bearings are self-aligning to compensate for shaft misalignment.

Steel bearings are stronger than stainless steel bearings, but not as corrosion resistant.

Stainless steel bearings are more corrosion resistant than steel bearings.

Sealed bearings block out dust and other contaminants better than shielded bearings.

Shielded bearings dissipate heat more efficiently than sealed bearings.

For technical drawings and 3-D models, click on a part number.

Shield couplings and bearings from dirt and debris while protecting fingers and tools from moving parts. Guards are electrically nonconductive, and resist chemicals, corrosion, and impact. They are OSHA compliant 29 CFR 1910.219 for rotating machinery. Guards come unassembled.