With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

A handle on the side of the carriage locks the carriage in place.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

Fasten loads on the side of these carriages and add linear motion to a T-slot assembly.

For applications with low clearance, these carriages protrude less than 5 mm above their rails.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

These tiny carriages and guide rails are sized for electronic and other precision applications.

With a plastic cage that surrounds the ball bearings to prevent them from colliding, these extra-wide carriages run quietly for many cycles without needing maintenance. All of these carriages have a wide base and low-profile design to stabilize moment (twisting) and off-center loads better than other carriages.

Mount along a wall or other vertical surface.

These track roller carriages and guide rails are stainless steel for use in wet, corrosive environments.

V-shaped rollers and rails allow these carriages to operate well in dirty environments because the debris won't get trapped on the rail.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

These steel track rollers and guide rails support loads up to 300 lbs.

Slides have a row of ball bearings on each side of the rail.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

A micrometer handle ensures accurate, repeatable positioning along a single axis—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

A linear scale and micrometer-like hand wheel measure travel distance in increments of 0.001".

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

With two bearings mounted in a single housing, these bearings have load capacities more than 10 times as high as standard mounted linear sleeve bearings. A ceramic liner helps them achieve high speeds as well as rapid acceleration and deceleration.

Designed to handle heavy loads, these bearings have the highest load capacities of any mounted linear ball bearings we offer.

Use the adjustment screw in the housing to tighten or loosen the snugness (also known as preload) of the bearing to your shaft.

The flanged housing makes these bearings a good solution for vertical linear motion applications.

The Frelon liner on these bearings allows them to stand up to a wider range of chemicals than other flange-mounted linear sleeve bearings.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

With two bearings mounted in a single housing, these bearings have higher load capacities than standard ones. A ceramic liner helps them achieve high speeds as well as rapid acceleration and deceleration.

Mount these bearings on a support rail shaft for applications requiring maximum rigidity.

With PTFE sleeve bearings and a low-friction ball screw, these slides don’t require the mess and maintenance of lubrication but still give you precise positioning anywhere along the length of their stroke.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.