These carriages and guide rails are steel.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

These carriages and guide rails are steel.

Designed for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

With a plastic cage that surrounds the ball bearings to prevent them from colliding, these extra-wide carriages run quietly for many cycles without needing maintenance. All of these carriages have a wide base and low-profile design to stabilize moment (twisting) and off-center loads better than other carriages.

Mount to vertical surfaces for applications where tight tolerances aren't required.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

The square profile prevents loads from twisting and rotating.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

For applications with low clearance, these carriages protrude less than 5 mm above their rails.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Combine with a T-slotted rail to add linear motion to your assembly.

Mount along a wall or other vertical surface.

These track roller carriages and guide rails are stainless steel for use in wet, corrosive environments.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

Made of stainless steel, these track rollers and guide rails are more corrosion resistant than steel rollers and rails.

Good for use in pick-and-place applications, machine tool doors, and telescopic press arms, these rugged slides are designed to carry heavy loads.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

A linear scale and micrometer-like hand wheel measure travel distance in increments of 0.001".

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

A micrometer handle ensures accurate, repeatable positioning along a single axis—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Position shafts an inch or two off the ground to maintain bearing and part clearance. Support rails provide stability over the entire length of shaft, allowing virtually unlimited travel lengths and eliminating bending under moderate to heavy loads.

At approximately one-third the height of standard versions, these rails provide linear shaft support in applications with low vertical clearance. They provide stability over the entire length of shaft, allow virtually unlimited travel lengths, and eliminate bending under moderate to heavy loads.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Loosen the clamping screw to install, then tighten to secure. Made of lightweight, corrosion-resistant aluminum, these shaft supports hold linear shafts perpendicular to the mounting surface. Use with light to medium loads where shaft alignment is not critical.

Slide the shaft in to install, then tighten to secure. For use with light to medium loads where shaft alignment is not critical, these shaft supports brace the end of a linear shaft along the ground or other flat surface.

Install these drawer slides in small-parts cabinets.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

With fewer moving parts than other lock-open drawer slides, these collect less debris for a longer service life.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

These slides automatically pull the drawer closed when it approaches the closed position.

A stop holds the drawer closed; pull firmly on the drawer to open.

These slides gradually slow the drawer's motion to prevent it from slamming open.