We will reply to your message within an hour.
Open these rings, pass them over the end of a shaft, and release to spring into the groove.
Thicker than standard external retaining rings, these rings withstand greater force.
These rings meet military specification MS 16624.
No groove is required for these rings—their thick profile helps them grip the shaft.
For a smooth profile and better clearance than standard external retaining rings, the lugs on these rings point inward.
The curved design of these rings works like a spring, taking up play for a tight hold.
Thicker than standard spiral rings, these rings withstand greater forces.
Slide these rings into place with one twist—no tools required—for applications with high thrust loads.
These coiled rings can be wound into place on a shaft without tools.
Often used with small engines, heavy equipment, and power transmission, these external retaining rings have speared ends to help you install and remove them.
Also known as E-style rings.
Also known as C-style and crescent rings, these rings have a small shoulder to fit in tight spaces.
These rings are reinforced to withstand faster rotation than other side‐mount retaining rings. Also known as reinforced E‐style rings.
Also known as bowed E-style rings, these have a curved design that works like a spring, taking up play for a tight hold.
Also known as poodle rings, these thick rings have "ears" that form a large retaining surface to withstand stronger forces than other side-mount retaining rings.
Also known as constant-section rings, these rings have open ends and a profile that does not taper like other external retaining rings. Use them with linear bearings on support rail shafts.
No groove required—press these rings onto the end of a shaft for a firm grip.
Also known as flat-style speed nuts, these have a large surface to distribute loads better than standard and flanged external push rings.
Use these caps to hold components in place and protect shaft ends.
The wide flange provides better load distribution than standard external push rings and can be used to cover oversized holes. Also known as thread cutting nuts.
Slide these rings into a groove near the end of the shaft and the tab locks them in place.
Also known as X-washers, place these rings into the groove and squeeze tight with pliers to form a 360° closure.
Squeeze these rings to place them in the groove inside a bore or housing.
Thicker and stronger than standard internal retaining rings, these withstand greater thrust loads.
For a smooth bore and better clearance than standard internal retaining rings, the lugs on these rings face outward.
With teeth along the inside, these retaining rings hold chamfered shafts inside the housing of your equipment.
Slide these rings into place by hand with a single twist for applications with high thrust loads.
These coiled rings can be wound into place inside a bore or housing without tools.
No groove required—these rings have teeth that firmly grip the bore.
These assortments include pliers to install external and internal rings.
Assortments include pliers to install external rings.
Wind these retaining rings into a groove—no tools required for installation.
Pull these rings open with retaining ring pliers, pass over the end of a shaft, and release to spring into a groove.
Assortments include pliers to install external and internal rings.
Also known as E-Style and C-style rings, slide these into the groove from the side of the shaft. They provide a wider shoulder than other external retaining rings for a larger retaining surface.
Pull ring ends together with retaining ring pliers and place into the bore of a shaft or housing.
Also called tolerance rings, these rings are for use in stamped, molded, or worn housings to form a tight hold on the bearings.
Also known as sleeve-bearing turntables or slewing-ring bearings.
Built-in detents slow or stop the rotation of the turntable at specified intervals for repeatable positioning.
A stop prevents the turntable from rotating all the way around.
With cylindrical rollers to distribute load over a large surface area, these bearings are often used to support heavy loads at high speeds in applications such as power generation and metal recycling.
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
Double rows of tapered bearings support large shafts with heavy loads.
Simplify tasks such as spray painting, repair work, and inspection. These turntables rotate to expose every side of an object while working.
Make sure you have the proper size driver for bearing, seal, and bushing installation jobs.
Prevent motor downtime by protecting bearings from stray currents generated by variable frequency drives. These grounding rings create a path for stray currents, so they won't damage bearing surfaces.