These carriages and guide rails are steel.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

These carriages and guide rails are steel.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

Run many cycles in tight spaces before replacing or re-greasing carriages.

With a plastic cage that surrounds the ball bearings to prevent them from colliding, these extra-wide carriages run quietly for many cycles without needing maintenance. All of these carriages have a wide base and low-profile design to stabilize moment (twisting) and off-center loads better than other carriages.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Use these carriages and guide rails in temperatures up to 300° F.

A handle on the side of the carriage locks the carriage in place.

Mate with a T-slotted rail to add linear motion to your assembly.

C-shaped guide rails grip the carriage around the outside to support linear motion along walls and other vertical surfaces.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

Made with Frelon bearings, these slides have over four times the load capacity of standard positioning slides.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

A micrometer handle ensures accurate, repeatable positioning along a single axis—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Choose ball bearings for debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

With two bearings mounted in one housing, these sleeve bearings can handle heavier loads than standard mounted linear sleeve bearings.

With two bearings mounted in a single housing, these bearings have load capacities more than 10 times as high as standard mounted linear sleeve bearings. A ceramic liner helps them achieve high speeds as well as rapid acceleration and deceleration.

The flanged housing makes these bearings a good solution for vertical linear motion applications.

The Frelon liner on these bearings allows them to stand up to a wider range of chemicals than other flange-mounted linear sleeve bearings.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard mounted linear ball bearings for support rail shafts.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

Sleeve bearings outperform ball bearings in dirty environments. Use them for low speed applications.

These bearings have a ceramic liner to help them achieve high speeds as well as rapid acceleration and deceleration.

Ball bearings create less friction than sleeve bearings, so they require less force to operate.

Use ball bearings in debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

The choice for low-friction motion in high-temperature environments.

Thinner than standard linear sleeve bearings, these bearings fit where clearance is a concern.

Use these ultra-thin sleeve bearings in high-speed applications where clearance is a concern.

Because they usually do not require lubrication, linear sleeve bearings outperform linear ball bearings in dirty environments.

Slide up to two linear ball or sleeve bearings into these housings and secure them with the included internal retaining rings.

These slides fully extend for convenient access to the back of drawers.

The stacked design provides stability for deep and wide drawers.

These slides automatically pull the drawer closed when it approaches the closed position.

Open drawers from either side of a cart or cabinet—these slides let drawers pass through for two-way access to contents.

A stop holds the drawer open; push firmly on the drawer to close.

These slides provide full extension for convenient access to the back of your drawers.

To prevent drawers from slamming shut and support them even if they’re tall and full of heavy equipment, these steel slides have soft-closing bumpers and mount to the top and bottom of drawers.

A stop holds the drawer closed; pull firmly on the drawer to open.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

At approximately one-third the height of standard versions, these rails provide linear shaft support in applications with low vertical clearance. They provide stability over the entire length of shaft, allow virtually unlimited travel lengths, and eliminate bending under moderate to heavy loads.

These shaft supports hold linear shafts perpendicular to the mounting surface.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.