McMaster-Carr logo
    Filter by
    Bearing Trade Number
    Industrial Info Snippet
    Attribute Image
    System of Measurement
    Shaft Diameter
    Attribute Image
    Bearing Seal Type
    Radial Clearance Trade Number
    Width
    Attribute Image
    Bearing Construction
    ABEC Rating
    Shaft Mount Type
    Bearing Type
    Ball Bearing Profile
    Shaft Type
    Dynamic Radial Load Capacity
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    5 Products

    Lubricant

    Performance

    Performance

    Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Ball Bearings, Shielded.

    Shielded

    Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.
    Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Inner Ring
    Type
    Bearing
    Trade No.
    Each
    Shielded
     
    Steel
    40801816,5008,500-20230Standard6208-2Z
    		5972K344000000
    40801837,3009,000-20230Standard6208-2Z
    		6661K4900000
     
    Corrosion-Resistant 440C Stainless Steel
    40801814,0009,100-40240Standard6208-2Z
    		6153K171000000
     

    High-Temperature Graphite-Lubricated Ball Bearings

    Image of Product. Front orientation. Ball Bearings. High-Temperature Graphite-Lubricated Ball Bearings.
    Keep parts spinning in industrial ovens and other places as hot as 660° F. Greased with graphite lubricant, these bearings stay slippery where oil would burn off or solidify. You can install and forget them since the lubricant lasts forever.
    Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Inner Ring
    Type
    Bearing
    Trade No.
    Each
    Shielded
     
    Steel
    40801817,300150-70660Standard6208-2Z
    		1258N350000000
     

    Electrically Insulating Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Electrically Insulating Ball Bearings, Shielded.

    Shielded

    Protect bearings from stray currents. The ceramic balls insulate bearings from electrical charges in electric motors and power generators that can damage the inner ring over time. The balls also generate less heat than metal ones, so you don’t have to lubricate them as often to keep bearings running smoothly.
    Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    Ceramic Balls
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Bearing
    Trade No.
    Each
    Shielded
     
    Steel
    40801816,50012,000-202506208-2Z
    		1389N360000000
     
    back to top