McMaster-Carr logo
    Filter by
    System of Measurement
    Shaft Diameter
    Attribute Image
    Bearing Trade Number
    Industrial Info Snippet
    Attribute Image
    Width
    Attribute Image
    Bearing Seal Type
    Ball Material
    Maximum Rotation Speed
    Shaft Type
    Material
    For Load Direction
    Radial Clearance Trade Number
    For Housing ID
    Attribute Image
    Rotation Speed
    Ball Bearing Profile
    Shaft Mount Type
    Bearing Construction
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Radial Clearance
    Shield Material
    Bearing Type
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    3 Products

    Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Ball Bearings, Shielded.

    Shielded

    Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.
    Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Inner Ring
    Type
    Bearing
    Trade No.
    Each
    Shielded
     
    Steel
    551002119,7506,300-20230Standard6211-2Z
    		00000000000000
    5510021310,3507,000-20230Standard6211-2Z
    		0000000000000
     

    Electrically Insulating Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Electrically Insulating Ball Bearings, Shielded.

    Shielded

    Protect bearings from stray currents. The ceramic balls insulate bearings from electrical charges in electric motors and power generators that can damage the inner ring over time. The balls also generate less heat than metal ones, so you don’t have to lubricate them as often to keep bearings running smoothly.
    Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    Ceramic Balls
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Bearing
    Trade No.
    Each
    Shielded
     
    Steel
    5510021111,4009,600-202456211-2Z
    		00000000000000
     
    back to top