System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
Ball Bearing Type Ball Bearing Type |
|---|
 | With Retaining Ring |
Bearing Trade Number Bearing TradeNumber  | Show |
|---|
Bearing Trade Number Bearing Trade Number | Hide |
|---|
Bearing Type Bearing Type |
|---|
 | Ball |
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Inner Ring Type Inner Ring Type |
|---|
 | Extended |
For Shaft Type For Shaft Type |
|---|
 | Round |
For Load Direction For Load Direction |
|---|
 | Radial |
ID ID |
|---|
|
Ring Material Ring Material |
|---|
|
Construction Construction |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
| ER20 | 1 1/4" | 2.8346" | 15/16" | 1.819" | 1.688" | 3.078" | 0.062" | 5,750 | 3,450 | 5,000 | -20° to 250° | Not Rated | 0000000 | 000000 |
Clamp-On Collar Ball Bearings
Quickly secure these bearings onto shafts with the clamp-on collar for a concentric, mar-free hold. Tighten the single screw on the locking collar around its inner ring on your shaft to center and secure the shaft in the bearing bore. The collar’s firm grip reduces vibration and noise in your system. The steel rings on these bearings have a black-oxide finish for some corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Sealed | |||||||||||||||
Black-Oxide Steel Ring | |||||||||||||||
| ER20 | 1 1/4" | 2 7/16" | 7/8" | 1.59375" | 1.5" | 2.656" | 0.063" | 4,350 | 2,550 | 7,600 | Lubricated | -20° to 220° | ABEC-1 | 0000000 | 0000000 |
| ER20 | 1 1/4" | 2 27/32" | 15/16" | 1.84375" | 1.688" | 3.078" | 0.063" | 5,750 | 3,450 | 6,500 | Lubricated | -20° to 220° | ABEC-1 | 0000000 | 000000 |