1 1/16" Housing ID Bearings

Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

							Temp. Range, ° F
	For Shaft Dia.	For Housing ID	Wd.	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type		Each
Open







				Steel

				1/4"	1 1/16"	1/4"	Not Rated	560	1,200	-20	250	Standard	0000000	00000


				5/16"	1 1/16"	3/8"	Not Rated	600	1,200	-20	250	Standard	0000000	00000
				3/8"	1 1/16"	3/8"	Not Rated	630	1,200	-20	250	Standard	0000000	0000

Flanged Ball Bearings

Open

Install these bearings inside a housing and they won't budge. The flange presses against the housing wall, so vibration and other sudden forces parallel to the shaft (thrust loads) won't knock them off-kilter.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.

				Flange					Temp. Range, ° F
	For Shaft Dia.	For Housing ID	Wd.	OD	Thk.	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type		Each
Open







				Steel

				3/8"	1 1/16"	3/8"	1.182"	0.06"	Not Rated	630	1,200	-20	250	Extended	00000000	00000


				7/16"	1 1/16"	3/8"	1.182"	0.06"	Not Rated	630	1,200	-20	250	Extended	00000000	0000

Oil-Embedded Flanged Sleeve Bearings

Install and forget these self-lubricating bearings. All are made from porous metal and saturated with oil to reduce maintenance and downtime. A good all-around choice, they are used in everything from palm-sized fans in electronics to tire-sized pulleys. Although these bearings will work in most conditions, oil may drip away if temperatures get too high. Consider a graphite-lubricated bearing for higher temperatures or places where you can’t afford the mess. All are fabricated, lubricated, and inspected in the U.S.

Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

High-Load 863 Iron Copper—Iron makes these bearings harder, stronger, and more resistant to sudden starts and stops than 841 bearing bronze. However, they operate at slower speeds. The increased iron content makes these bearings appear silver.

Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away at higher temperatures.

	For Housing ID	Lg.	Flange OD	Flange Thk.	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	3/4"	1 1/16"	1 3/16"	1 3/16"	1/8"	1,750 lb. @ 60 rpm	1,300 lb. @ 60 rpm	Synthetic Oil	-35 to 300	00000000	000000


	High-Load 863 Iron Copper



			3/4"	1 1/16"	1 3/16"	1 3/16"	1/8"	2,600 lb. @ 60 rpm	1,200 lb. @ 60 rpm	Synthetic Oil	-15 to 300	00000000	00000

High-Temperature Graphite-Lubricated Sleeve Bearings

Made of a graphite and metal alloy, these bearings stay slippery at high temperatures where oil burns off and other bearings fail. With no need for refills, they require little to no maintenance. You’ll find them in pumps, propellers, and mixers that spin near steam or inside ovens. However, graphite may eventually flake off, dropping flecks and leaving smudges. If you need a spic-and-span space, consider dry-running bearings made of slippery plastic instead. All are fabricated, lubricated, and inspected in the U.S.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

Extreme-Temperature Chemical-Resistant Graphalloy—From the freezer to the furnace, these bearings glide in extreme temperatures where other bearings grind and fail. They resist decay caused by the strong acids or bases found in cleaning fluids. They even work underwater without swelling or warping.

	For Housing ID	Lg.	Dynamic Radial Load Cap. @ Speed	Temp. Range, ° F		Each
Extreme-Temperature Chemical-Resistant Graphalloy



	11/16"	1 1/16"	1"	510 lb. @ 60 rpm	-450 to 750	0000000	000000

Oil-Embedded Sleeve Bearings

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

Mineral Oil Base—Mineral oil consistently lubricates at most temperatures but doesn’t last as long as synthetic oil.

	For Housing ID	Lg.	Dynamic Radial Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	3/4"	1 1/16"	1"	1,500 lb. @ 60 rpm	Synthetic Oil	-35 to 300	00000000	00000


	3/4"	1 1/16"	1 1/4"	1,850 lb. @ 60 rpm	Synthetic Oil	-35 to 300	00000000	0000
	15/16"	1 1/16"	3/4"	1,400 lb. @ 60 rpm	Mineral Oil	10 to 220	00000000	0000
	15/16"	1 1/16"	1 1/4"	2,300 lb. @ 60 rpm	Mineral Oil	10 to 220	00000000	0000

Dry-Running Metal-Reinforced Plastic Sleeve Bearings

Combine slippery plastic with the strength of metal. The PTFE core is naturally slippery, so you’ll never have to add lubricant. These bearings also keep your workspace clean with no lubricant to drip or flake and attract dust. Compared to all-metal bearings, they are lighter.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

PTFE with 17-4 PH Stainless Steel Shell—The highest load capacity of any sleeve bearing we offer. 17-4 PH stainless steel offers good corrosion resistance but is heavier than aluminum.

	For Housing ID	Lg.	Dynamic Radial Load Cap. @ Speed	Temp. Range, ° F	Specs. Met		Each
PTFE with 17-4 PH Stainless Steel Shell



	7/8"	1 1/16"	1"	15,250 lb. @ 20 rpm	-60 to 320	SAE AS81820, SAE AS81934, MIL-B-81820, MIL-B-81934	0000000	0000000

Flanged Sleeve Bearings

These bearings don’t come with a lubricant, so you can select the oil that meets the needs of your application. You’ll need to refill the oil, so make sure the bearing is located where you can access it. All are fabricated and inspected in the U.S.

High-Load 932 Bearing Bronze—These bearings are strong enough for sudden starts and stops, plus they resist wear and tear. They are cast from an alloy of leaded tin bronze for uniform rigidity and strength. Also known as 660 leaded bronze bearings.

	For Housing ID	Lg.	Flange OD	Flange Thk.	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Temp. Range, ° F		Each
High-Load 932 Bearing Bronze



	3/4"	1 1/16"	1 3/16"	1 3/16"	1/8"	3,350 lb. @ 60 rpm	2,650 lb. @ 60 rpm	-350 to 450	00000000	000000