McMaster-Carr logo
    Filter by
    System of Measurement
    Shaft Diameter
    Attribute Image
    Bearing Seal Type
    Bearing Type
    Industrial Info Compare
    Bearing Trade Number
    Industrial Info Snippet
    Attribute Image
    For Housing ID
    Attribute Image
    Roller Bearing Type
    Shaft Type
    Ball Bearing Profile
    Shaft Mount Type
    Bearing Construction
    Dynamic Radial Load Capacity
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    7 Products

    Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Ball Bearings, Open.

    Open

    Image of Product. Front orientation. Ball Bearings. Ball Bearings, Shielded.

    Shielded

    Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.
    Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.
    Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Inner Ring
    Type
    Bearing
    Trade No.
    Each
    Open
     
    Steel
    4558711,35013,000-50130Standard680900000000000000
     
    Shielded
     
    Steel
    4558711,35011,000-40150Standard6809-2Z0000000000000
     

    Permanently Lubricated Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Permanently Lubricated Ball Bearings.
    Install and forget these self-lubricating bearings. Their lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.
    Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
    Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Inner Ring
    Type
    Bearing Trade
    No.
    Each
    Sealed
     
    Corrosion-Resistant 440C Stainless Steel
    4558711,3506,000-10200Standard6809-2RS
    000000000000000
     

    Needle-Roller Bearings

    Image of Product. Front orientation. Roller Bearings. Needle-Roller Bearings.
    Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.
    Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.
    Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.
    Radial Load
    Cap., lb.
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    Dynamic
    Static
    Max. Rotation
    Speed, rpm
    Lubrication
    For Shaft Surface
    Smoothness, Ra, μin
    Temp. Range,
    ° F
    Specs. Met
    Each
    For Radial Load—Open with Steel Ring
    5058258,65018,8505,300Required8-20 to 280DIN 618, ISO 324500000000000000
     
    For Radial Load—Sealed on Both Sides with Steel Ring
    5058246,95014,1503,150Lubricated80 to 210DIN 6180000000000000
     

    Combination Ball/Needle-Roller Bearings

    Image of Product. Front orientation. Roller Bearings. Combination Ball/Needle-Roller Bearings.
    Image of Attribute. Side1 orientation. Contains Annotated. Combination Ball/Needle-Roller Bearings.
    A built-in thrust ball bearing reduces wear from adjacent shaft components, while the needle rollers support high radial loads. Install anywhere you would use separate bearings for radial and thrust loads.
    Radial Load
    Cap., lb.
    Thrust Load
    Cap., lb.
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    Ball Bearing
    OD, mm
    Ball Bearing
    Wd., mm
    Dynamic
    Static
    Dynamic
    Static
    Max. Rotation
    Speed, rpm
    Lubrication
    For Shaft Surface
    Smoothness, Ra, μin
    Temp. Range,
    ° F
    Features
    Each
    For Combined Radial and Thrust Load—Open with Steel Ring
    45583266.5145,60011,6006,25012,3804,500Required8-20 to 230Lubrication Groove, Lubrication Hole000000000000000
     

    Ball Bearings for Food and Beverage

    Image of Product. Front orientation. Ball Bearings. Ball Bearings for Food and Beverage, Sealed.

    Sealed

    Food production rolls along smoothly on these bearings. Greased with FDA-compliant lubricant, they’re safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. The lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.
    Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
    Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Wd.,
    mm
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Inner Ring
    Type
    Food Industry Std.
    Bearing Trade
    No.
    Each
    Sealed
     
    Corrosion-Resistant 440C Stainless Steel
    4558711,1506,000-40200StandardFDA Compliant 21 CFR 178.35706809-2RS
    000000000000000
     
    back to top