System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter | Show |
|---|
|
For Shaft Diameter For Shaft Diameter | Hide |
|---|
For Load Direction For Load Direction |
|---|
 | Radial |
 | Combined Radial and Thrust |
 | Thrust |
Ball Bearing Type Ball Bearing Type |
|---|
 |  |  |
| Standard | Flanged | With Retaining Ring |
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
Mounted Bearing Type Mounted Bearing Type |
|---|
 | Base Mount |
Dynamic Thrust Load Capacity Dynamic Thrust Load Capacity |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
Lubrication Lubrication |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Plain Bearings
More
About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
Flanged bearings have a flange that ensures proper positioning inside a tube or housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
| ER26 | 1 5/8" | 3.347" | 1 3/32" | 2.2969" | 1.9375" | 3 19/32" | 0.0625" | 7,900 | 5,100 | 3,800 | -20° to 220° | ABEC-1 | 0000000 | 0000000 |
Steel—Flanged | ||||||||||||||
| GYA110RRB | 1 5/8" | 3.3465" | 0.866" | 2.2813" | 1.6555" | __ | __ | 8,150 | 4,500 | 4,200 | -65° to 250° | ABEC-1 | 0000000 | 000000 |
One-Piece Thrust Ball Bearings
In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Shielded | |||||||||||
| 1 5/8" | 2 31/32" | 13/16" | Steel | 10,300 | 25,000 | 2,400 | Required | -40° to 250° | Lubrication Hole | 00000000 | 000000 |
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 1 5/8" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1 7/8" | 1" | 3,250 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 00000 |
| 1 7/8" | 1 1/4" | 4,050 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 0000 |
| 1 7/8" | 1 1/2" | 4,700 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 1 7/8" | 1 3/4" | 5,650 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 00000 |
| 1 7/8" | 2" | 6,500 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 2" | 1 1/2" | 4,850 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 2" | 2" | 6,500 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 2" | 2 1/2" | 8,100 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 00000 |
| 2" | 3" | 9,400 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
Oil-Embedded Flanged Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
841 Bearing Bronze Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 1 5/8" Shaft Dia. | ||||||||||
| 2" | 2" | 2 1/4" | 3/16" | 6,500 lbs. @ 30 rpm | 3,800 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
High-Load Oil-Embedded Flanged Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes these bearings to release a thin layer of oil onto their surface. Color is silver because of the iron.
863 iron-copper bearings are also known as Super Oilite® bearings.
Iron-copper bearings support heavier loads than 863 iron-copper bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 1 5/8" Shaft Dia. | ||||||||||
| 2" | 2" | 2 1/4" | 3/16" | 8,900 lbs. @ 30 rpm | 3,750 lbs. @ 30 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 0000000 | 000000 |
Iron-Copper Bearings | ||||||||||
For 1 5/8" Shaft Dia. | ||||||||||
| 2" | 2" | 2 1/4" | 3/16" | 19,050 lbs. @ 30 rpm | 8,050 lbs. @ 30 rpm | Lubricated | SAE 90 Oil | 10° to 220° | 0000000 | 00000 |
Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
841 Bronze Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 1 5/8" Shaft Dia. | ||||||||||
| 2" | 2" | 2 1/4" | 3/16" | 7,300 lbs. @ 30 rpm | 3,750 lbs. @ 30 rpm | Lubricated | ISO 68 Oil | -140° to 460° | 00000000 | 000000 |
Multipurpose Flanged Sleeve Bearings
These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 932 bronze bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Temperature Range, °F | Each | |
660 Leaded Bronze Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 1 5/8" Shaft Dia. | |||||||||
| 2" | 2" | 2 1/4" | 3/16" | 13,000 lbs. @ 30 rpm | 7,600 lbs. @ 30 rpm | Required | -350° to 450° | 00000000 | 000000 |
Needle-Roller Bearings
Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Specifications Met | Each | |
Open | ||||||||||||
| 1 5/8" | 2" | 5/8" | Steel | 5,700 | 8,900 | 6,800 | Required | 8 | -40° to 280° | __ | 00000000 | 000000 |
| 1 5/8" | 2" | 1 1/4" | Steel | 11,400 | 21,800 | 6,000 | Required | 8 | -20° to 280° | DIN 281, ISO 76 | 00000000 | 00000 |
Tapered-Roller Thrust Bearings
Thick, tapered rollers stand up to extremely high thrust loads.
Open bearings dissipate heat more efficiently than sealed bearings.
Sealed bearings have better dust resistance than open bearings, but retain more heat.
For technical drawings and 3-D models, click on a part number.
Mounted Roller Bearings
Roller bearings have a thinner profile and larger contact area than ball bearings, making them stronger and more space-efficient than ball bearings.
Sealed bearings block out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Dynamic Thrust Load Cap., lbs. | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Steel Bearings with Cast Iron Housing—Shaft Mount Type: Set Screw | ||||||||||||||||
| 1 5/8" | 2 1/8" | 4 1/4" | 7 7/8" | 3 3/8" | 3/4" | 5/8" | 6 1/4" | 7,850 | 33,000 | 2,550 | 3,300 | -60° to 250° | Fixed Alignment | Lubricated | 0000000 | 0000000 |
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
SD Style Bushing | ||||||||
| 1 5/8" | 2 3/32" | 3/8" | 3/16" | 108 | Steel | Clamping Screws | 00000000 | 000000 |
SDS Style Bushing | ||||||||
| 1 5/8" | 1 21/32" | 3/8" | 3/16" | 108 | Steel | Clamping Screws | 00000000 | 00000 |
SF Style Bushing | ||||||||
| 1 5/8" | 2 1/2" | 3/8" | 3/16" | 360 | Steel | Clamping Screws | 00000000 | 00000 |
SH Style Bushing | ||||||||
| 1 5/8" | 1 19/32" | 3/8" | 1/16" | 108 | Steel | Clamping Screws, Machine Key | 00000000 | 00000 |
SK Style Bushing | ||||||||
| 1 5/8" | 2 9/32" | 3/8" | 3/16" | 180 | Steel | Clamping Screws | 00000000 | 00000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
1610 Style Bushing | |||||||||
| 1 5/8" | 1" | 3/8" | 1/8" | 8° | 175 | Steel | Machine Key, Set Screws | 000000000 | 000000 |
1615 Style Bushing | |||||||||
| 1 5/8" | 1 1/2" | 3/8" | 1/8" | 8° | 175 | Steel | Machine Key, Set Screws | 000000000 | 00000 |
2012 Style Bushing | |||||||||
| 1 5/8" | 1 1/4" | 3/8" | 3/16" | 8° | 280 | Steel | Set Screws | 000000000 | 00000 |
2517 Style Bushing | |||||||||
| 1 5/8" | 1 3/4" | 3/8" | 3/16" | 8° | 430 | Steel | Set Screws | 000000000 | 00000 |
3020 Style Bushing | |||||||||
| 1 5/8" | 2" | 3/8" | 3/16" | 8° | 800 | Steel | Set Screws | 000000000 | 00000 |
Split-Tapered Bushings
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
Bushings with a machine key fit into a matching keyway on a sprocket or pulley for high-torque applications.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||
|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Each | |
Steel | |||||||
P1 Style Bushing with Machine Key | |||||||
| 1 5/8" | 1 15/16" | 3/8" | 3/16" | 3° | 192 | 00000000 | 000000 |
P2 Style Bushing with Machine Key | |||||||
| 1 5/8" | 2 15/16" | 3/8" | 3/16" | 3° | 192 | 00000000 | 00000 |
Q1 Style Bushing with Machine Key | |||||||
| 1 5/8" | 2 1/2" | 3/8" | 3/16" | 3° | 348 | 00000000 | 00000 |