A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. Because it's solid, the lubricant blocks out water and dust, extending the life of the bearing.

With a spherical raceway and two rows of balls, these bearings compensate for shaft misalignment.

A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. Bearings are 440C stainless steel.

Good for applications with incidental food contact, these 440C stainless steel bearings have a food-grade, solid polymer lubricant between the balls and race that eliminates the need for additional lubrication.

Made of slippery plastic, these bearings do not require lubrication and have excellent corrosion and chemical resistance.

Made of PVDF, these bearings resist moisture absorption, so they won’t warp in underwater applications.

No need to worry about precisely aligning these bearings—they swivel to compensate for up to 5° of shaft misalignment.

Unlike other ball bearings, these do not need to be fully inserted into a housing. A spline around the outside of the bearing creates a permanent, secure hold in thin panels.

These bearings have twice as many contact points as angular-contact ball bearings.

A combination of stainless steel and nylon components provide increased corrosion resistance over standard thrust ball bearings.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

With a flexible layer of rubber sandwiched between an oil-embedded bronze bearing and rigid metal shell, these bearings reduce wear and machinery noise.

The oil in these bearings is suitable for incidental contact with food.

Use these bearings for frequent starts and stops in high-load applications.

Use where high loads and speeds are not required.

Graphite provides a layer of dry lubrication that can operate in high-temperature environments.

These bearings stand up to a wider range of chemicals than other dry-running sleeve bearings.

Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts.

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

The oil in these bearings is suitable for incidental contact with food.

With oil for reduced friction and iron for added strength, these bearings handle frequent stops and starts in high-load applications.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

Good for underwater applications, these bearings won’t swell or warp when wet.

Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.

Compensating for minor shaft misalignment and not requiring lubrication, these sleeve bearings swivel to self-align and are dry running. They don’t need a housing and you can install and replace them without any tools because they’re slip fit.

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

The oil in these bearings is suitable for incidental contact with food.

Use these bearings for frequent starts and stops in high-load applications. For low friction coefficients, they release a thin layer of an embedded PTFE lubricant during startup friction.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Good for underwater applications, these bearings won’t swell or warp when wet.

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

With a considerably larger ID than our Face-Mount Crossed-Roller Bearings, use these to run hydraulic lines, electrical wiring, and other components through the inside of the bearing.

These bearings have higher radial load capacity, speed, and accuracy than standard needle-roller bearings.

The needles in these bearings roll freely in one direction, but lock to transmit torque when the rotation of the shaft is reversed. Also known as drawn-cup roller clutches.

Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.

Made from slippery materials, these bearings reduce friction without the oily mess.

Made of acetal blended with PTFE, these bearings handle speeds twice as fast as standard sleeve bearings.

Roller bearings have a thinner profile and larger contact area than ball bearings, making them stronger and more space-efficient than ball bearings.

Use these nylon or acetal bearings for light loads. The closed backing blocks out dust and other contaminants.

Handling speeds twice as fast as standard mounted sleeve bearings while limiting wear on your system, these bearings are made of PTFE-filled acetal.

These roller bearings handle extremely high speeds for their small size.

The choice for low-friction motion in high-temperature environments.

Ridges on the inside of these bearings wipe away dust and debris as the bearing travels on a shaft.

Use these ultra-thin sleeve bearings in high-speed applications where clearance is a concern.

With a grooved inner diameter, these bearings are designed to work with splined shafts. Together, they transmit rotary power while allowing the bearing to move freely along the length of the shaft. All are for use where shaft misalignment is unlikely.

Choose ball bearings for debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Made from a single piece of slippery UHMW plastic, these bearings have no cracks or crevices so they’re easy to clean.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end.