System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter | Show |
|---|
|
For Shaft Diameter For Shaft Diameter | Hide |
|---|
Inner Ring Type Inner Ring Type |
|---|
 | Extended |
Bearing Trade Number Bearing Trade Number |
|---|
|
Plain Bearing Type Plain Bearing Type |
|---|
 | Sleeve |
Ball Bearing Type Ball Bearing Type |
|---|
 | With Retaining Ring |
Cage Material Cage Material |
|---|
|
Ball Material Ball Material |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
About Plain Bearings
More
About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Steel—With Retaining Ring | ||||||||||||||
| 7613-2RS | 13/16" | 2" | 5/8" | 1.306" | 1.179" | 2.156" | 0.042" | 2,950 | 1,350 | 5,000 | -20° to 250° | Not Rated | 0000000 | 000000 |
Thrust Ball Bearings for Shaft Ends
Use these bearings as miniature high-precision turntables. They have a unique design that allows your shaft to sit on top of the bearing rather than being inserted through it. Bearings can be bonded to a mounting plate or press-fit into a hole.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Open | ||||||||||
| 13/16" | 13/16" | 5/8" | Steel | 2,150 | 3,500 | 1,500 | Required | -40° to 250° | 00000000 | 000000 |
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 13/16" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1" | 7/8" | 1,400 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 00000 |
| 1" | 1" | 1,600 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 0000 |
| 1" | 1 1/4" | 2,000 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 1" | 1 1/2" | 2,250 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 0000000 | 00000 |
| 1" | 1 3/4" | 2,800 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 0000 |
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
JA Style Bushing | ||||||||
| 13/16" | 1 21/64" | 3/16" | 3/32" | 60 | Steel | Clamping Screws | 00000000 | 000000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
1610 Style Bushing | |||||||||
| 13/16" | 1" | 3/16" | 3/32" | 8° | 175 | Steel | Set Screws | 000000000 | 000000 |