System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter | Show |
|---|
|
For Shaft Diameter For Shaft Diameter | Hide |
|---|
For Load Direction For Load Direction |
|---|
 | Radial |
Maximum Speed Maximum Speed |
|---|
|
Plain Bearing Type Plain Bearing Type |
|---|
 | Sleeve |
Seal Type Seal Type |
|---|
|
Bearing Trade Number Bearing Trade Number |
|---|
Lubricant Lubricant |
|---|
|
Lubrication Lubrication |
|---|
|
Ball Bearing Type Ball Bearing Type |
|---|
 | With Retaining Ring |
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
About Plain Bearings
More
About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
| ER38 | 2 3/8" | 4.331" | 1 1/4" | 2.9844" | 2.5625" | 4 37/64" | 0.09375" | 11,750 | 8,150 | 3,000 | -20° to 220° | ABEC-1 | 0000000 | 0000000 |
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 2 3/8" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 2 5/8" | 1 1/4" | 5,700 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
| 2 5/8" | 1 5/8" | 7,700 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 00000 |
| 2 3/4" | 2" | 9,400 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 2 3/4" | 2 1/2" | 11,850 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 00000 |
| 2 3/4" | 3" | 14,000 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.