2.5mm Bearings | McMaster-Carr

Filter by

System of Measurement

Shaft Diameter

Ball Bearing Profile

Width

Bearing Type

For Housing ID

For Load Direction

Combined Radial and Thrust

Bearing Seal Type

Inner Ring Type

Plain Bearing Type

Lubricant

Length

Shaft Type

Lubrication

Shaft Mount Type

Ball Material

Material

Bearing Trade Number

Bearing Construction

RoHS

DFARS Specialty Metals

Exempt

Export Control Classification Number (ECCN)

REACH

Minimum Temperature

5 Products

Flanged Ball Bearings

Shielded

Install these bearings inside a housing and they won't budge. The flange presses against the housing wall, so vibration and other sudden forces parallel to the shaft (thrust loads) won't knock them off-kilter.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

				Flange, mm					Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	OD	Thk.	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Shielded







				Steel

				2.5	6	2.6	7.1	0.8	3	40	81,000	-50	300	Standard	682-2Z	000000000	000000

High-Precision Ball Bearings

Shielded

The most precise bearings we offer, with tolerances tighter than a speck of dust. Rated ABEC 7 out of 9, they meet strict tolerance standards established by the Annular Bearing Engineers Committee (ABEC). You'll find them in equipment that requires both high speed and pinpoint accuracy, such as gyroscopes.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type		Each
Shielded







				Corrosion-Resistant 440C Stainless Steel

				2.5	8	2.8	7	55	76,000	-30	280	Standard	0000000	000000

Oil-Embedded Flanged Sleeve Bearings

Install and forget these self-lubricating bearings. All are made from porous metal and saturated with oil to reduce maintenance and downtime. A good all-around choice, they are used in everything from palm-sized fans in electronics to tire-sized pulleys. Although these bearings will work in most conditions, oil may drip away if temperatures get too high. Consider a graphite-lubricated bearing for higher temperatures or places where you can’t afford the mess. All are fabricated, lubricated, and inspected in the U.S.

Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

High-Load 863 Iron Copper—Iron makes these bearings harder, stronger, and more resistant to sudden starts and stops than 841 bearing bronze. However, they operate at slower speeds. The increased iron content makes these bearings appear silver.

Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away at higher temperatures.

	For Housing ID, mm	Lg., mm	Flange OD, mm	Flange Thk., mm	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	2.5	6.5	4	8.5	2	31 lb. @ 120 rpm	160 lb. @ 120 rpm	Synthetic Oil	-35 to 300	0000000	000000


	High-Load 863 Iron Copper



			2.5	6.5	4	8.5	2	60 lb. @ 120 rpm	260 lb. @ 120 rpm	Synthetic Oil	-15 to 300	00000000	00000

Oil-Embedded Sleeve Bearings

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	2.5	6.5	4	31 lb. @ 120 rpm	Synthetic Oil	-35 to 300	0000000	000000