System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter | Show |
|---|
|
For Shaft Diameter For Shaft Diameter | Hide |
|---|
Mounted Bearing Type Mounted Bearing Type |
|---|
 |  |
| Base Mount | Four-Bolt Flange Mount |
 | |
| Thread Mount |
Bearing Trade Number Bearing Trade Number |
|---|
|
Bearing Type Bearing Type |
|---|
 | Ball |
Shaft Mount Type Shaft Mount Type |
|---|
|
Housing Material Housing Material |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
|
Seal Type Seal Type |
|---|
|
For Load Direction For Load Direction |
|---|
 | Radial |
Alignment Style Alignment Style |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Grease Fitting Thread Type Grease Fitting Thread Type |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
|
About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
| ER39 | 2 7/16" | 4.331" | 1 1/4" | 2.9844" | 2.5625" | 4 37/64" | 0.09375" | 11,750 | 8,150 | 3,000 | -20° to 220° | ABEC-1 | 0000000 | 0000000 |
| ER39 | 2 7/16" | 4.331" | 1 1/4" | 3.0156" | 2.5625" | 4 37/64" | 0.09375" | 13,100 | 8,080 | 2,800 | -65° to 250° | ABEC-1 | 0000000 | 000000 |
Washdown Clamp-On Collar Ball Bearings
Designed to stand up to frequent washdowns, you can quickly secure these ball bearings onto shafts with the clamp-on collar in food, beverage, pharmaceutical, and chemical plants. The collar centers your shafts and secures them better than set screw ball bearings, which reduces vibration and noise. To install these bearings, tighten the single screw on the collar around its inner ring on your shaft for a mar-free hold.
Coated with nickel, the steel rings on these bearings won’t corrode from water and harsh cleaners, similar to 304 stainless steel. The inner ring is extended for added shaft support. All of these bearings have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Capacity, lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | OD | OD Tolerance | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Sealed | |||||||||||||||
Nickel-Coated Steel Ring | |||||||||||||||
| 2 7/16" | 4.331" | 1 1/4" | 3.90625" | Not Rated | 2.625" | 4.57813" | 0.09375" | 13,950 | 8,150 | 1,250 | Lubricated | -20° to 220° | ABEC-1 | 0000000 | 0000000 |
Washdown Set Screw Collar Ball Bearings
Secure these bearings in washdown areas, such as food, beverage, pharmaceutical, and chemical plants, by tightening the set screw onto a shaft—no additional collar needed. Similar to 304 stainless steel, the nickel-coated steel rings on these bearings won’t break down from water. The extended inner ring increases shaft support. All of these bearings have NSF registered H1 lubrication, which is certified for incidental contact with food.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Seal Type | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Environmental Rating | Each | |
Nickel-Coated Steel Ring | ||||||||||||||||
| 2 7/16" | 4.331" | 1 1/4" | 3.90625" | 2.5625" | 4.57813" | 0.09375" | Sealed | 7,850 | 8,100 | 1,250 | Lubricated | -20 to 220 | ABEC-1 | IP69K | 0000000 | 0000000 |
Mounted Ball Bearings
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 2 7/16" | 2 3/4" | 5 15/16" | 9 1/2" | 2 3/4" | 1" | 5/8" | 7 1/4" | 11,700 | 8,150 | 3,000 | -20° to 220° | Self Aligning | Lubricated | 0000000 | 0000000 |
Permanently Lubricated Mounted Ball Bearings
A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. Seals block out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 2 7/16" | 2 3/4" | 5 7/16" | 9 1/2" | 2 15/16" | 1 5/32" | 23/32" | 7 13/32" | 11,800 lbs. | 8,150 lbs. | 2,400 | 10° to 175° | Self Aligning | Lubricated | 000000 | 0000000 |
High-Speed Mounted Ball Bearings
These bearings have the highest speed ratings of any mounted ball bearing that we offer. The clamp-on collar creates a 360° grip around the shaft for a strong, mar-free hold. Bearings are self-aligning to compensate for shaft misalignment.
Sealed bearings block out dust and other contaminants better than shielded bearings.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing—Shaft Mount Type: Clamp On | |||||||||||||||
Without Torque Indicator | |||||||||||||||
| 2 7/16" | 2 3/4" | 5 15/16" | 9 1/2" | 3 1/4" | 1" | 11/16" | 7 1/4" | 11,700 | 8,150 | 4,100 | -20° to 200° | Self Aligning | Lubricated | 0000000 | 0000000 |
Washdown Mounted Ball Bearings
Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. They have excellent corrosion resistance and prevent rusting caused by salt water, chlorine solutions, and chemicals because their housing is 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.
Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Dp. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Specifications Met | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 2 7/16" | 2 3/4" | 5 9/16" | 9 1/2" | 5 5/32" | 0.875" | 7 1/4" | 11,750 | 8,150 | 1,250 | -20° to 220° | Self Aligning | Lubricated | NSF Registered H1 | 0000000 | 0000000 |
| For Shaft Diameter | OD | Material | Mount Type | Temperature Range,°F | Specifications Met | Each | |
Closed | |||||||
|---|---|---|---|---|---|---|---|
| 2 3/8", 2 7/16", 60mm | 4 5/8", 117mm | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 000000 |
Open | |||||||
| 2 3/8", 2 7/16", 60mm | 4 11/16", 119mm | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 00000 |
Permanently Lubricated Washdown Mounted Ball Bearings with Four-Bolt Flange
Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. With a 316 stainless steel housing, these bearings won’t rust from salt water, chlorine, or chemicals. All are lubricated with NSF registered H1 grease, which is certified for incidental contact with food.
Set-screw bearings secure to shafts as you tighten their screw. They don’t need a collar; however, the screws leave some marring on the shaft.
Concentric-lock bearings have a collar that centers and secures the shaft in the bearing bore. To install, tighten the single screw on the collar around its inner ring on your shaft. These bearings have a secure grip on the shaft that reduces vibration and noise.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Capacity, lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Height | Length | Width | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Environmental Rating | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
| 2 7/16" | 2 11/16" | 6 7/8" | 3 51/64" | 13/16" | 5/8" | 5 5/8" | 11,700 | 3,490 | 1,250 | -20° to 220° | Self Aligning | IP69K | 0000000 | 0000000 |
Shaft Mount Type: Concentric Lock | ||||||||||||||
| 2 7/16" | 2 11/16" | 6 7/8" | 3 51/64" | 13/16" | 5/8" | 5 5/8" | 11,700 | 8,150 | 1,250 | -20° to 220° | Self Aligning | IP69K | 0000000 | 000000 |
Washdown Mounted Ball Bearings with Four-Bolt Flange
Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. They have excellent corrosion resistance and prevent rusting caused by salt water, chlorine solutions, and chemicals because their housing is 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.
Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Specifications Met | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 2 7/16" | 6 7/8" | 6 7/8" | 3 51/64" | 13/16" | 5/8" | 5 5/8" | 11,750 | 8,510 | 1,250 | -20° to 220° | Self Aligning | Lubricated | NSF Registered H1 | 00000000 | 0000000 |
| For Shaft Diameter | OD | Material | Mount Type | Temperature Range,°F | Specifications Met | Each | |
Closed | |||||||
|---|---|---|---|---|---|---|---|
| 2 3/8", 2 7/16", 60mm | 4 5/8", 117mm | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 000000 |
Open | |||||||
| 2 3/8", 2 7/16", 60mm | 4 11/16", 119mm | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 00000 |
Insert Bearings
Swap out worn inserts instead of replacing the entire mounted unit. Use the manufacturer model number on your existing mounted bearing to choose a compatible insert. Inserts must be used with the manufacturer model number specified.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | For Mounted Bearing Model No. | Each | |
Sealmaster Steel Insert Bearings | |||
|---|---|---|---|
Shaft Mount Type: Set Screw | |||
| 2 7/16" | NP-39, NPG-39-12, NPG-39-18, NPL-39, SC-39, SCHB-39, SEHB-39, SF-39, SFC-39, SP-39, ST-39, STH-39-12, STH-39-18 | 00000000 | 0000000 |
Thread-Mount Bearings
Combine with threaded pipe to mount these bearings in a variety of positions without the need for a flat mounting surface. Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
NPSM (National Pipe Straight Mechanical) threads are compatible with NPT threads. See more about pipe thread type and sizing.
For technical drawings and 3-D models, click on a part number.
Overall | Radial Load Cap., lbs. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Pipe Size | Thread Type | Thread Lg. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Ductile Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 2 7/16" | 4" | 6 13/16" | 5 5/8" | 2 9/16" | 1 1/4 | NPSM | 1 1/8" | 11,700 | 8,150 | 3,000 | -20° to 220° | Self Aligning | Lubricated | 000000 | 0000000 |
Screw Conveyors
Add on to an existing screw conveyor or keep it running like new.
Coupling shafts connect two screws together. End shafts support the end conveyor section. Coupling bolts connect shafts to the screw.
End-shaft seals prevent material contamination and discharge.
End-shaft bearings support the end of the shaft and help the screw rotate.
Bearing hangers mount inside the trough.
Hardwood bearings are oil impregnated and are often used in agricultural applications. UHMW bearings work well with chemicals and wet environments. Iron bearings are oil impregnated and offer longer life for abrasive materials.
For technical drawings and 3-D models, click on a part number.
