McMaster-Carr logo
    Filter by
    System of Measurement
    Bearing Type
    Industrial Info Compare
    Dynamic Thrust Load Capacity
    Bearing Seal Type
    Plain Bearing Type
    For Load Direction
    Cage Material
    Maximum Rotation Speed
    Shaft Type
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Roller Bearing Type
    Static Thrust Load Capacity
    For Shaft Surface Smoothness, Ra
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    4 Products

    Needle-Roller Thrust Bearings

    Image of Product. Bearings. Front orientation. Thrust Bearings. Needle-Roller Thrust Bearings.
    Image of Product. Front orientation. Thrust Roller Bearing Washers.

    Bearings

    Washers

    Small but mighty, our thinnest rolling thrust bearings slot into tight spaces and spin at whirring speeds. Their long, slender rollers support thrust loads and reduce friction in everything from machine tool spindles to gearboxes.
    A cage holds the rollers in place. You can install these bearings without washers between hardened, ground surfaces for the thinnest profile. If you’re working with unhardened, unground surfaces, you’ll need two washers for the rollers to run on. This three-piece design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    Thrust Bearings
    Thin Washers
    Thick Washers
    For Shaft
    Dia.
    OD
    Thk.
    Cage
    Material
    Dynamic Thrust
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Temp. Range,
    ° F
    Each
    Thk.
    Each
    Thk.
    Each
    Steel
    3 3/4"4 5/8"1/8"Steel12,6003,5000 to 2405909K9560000001/32"5909K9760000001/16"5909K985000000
     

    Washers for Needle-Roller Thrust Bearings

    Image of Product. Front orientation. Thrust Roller Bearing Washers.
    Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
    For Shaft
    Dia.
    OD
    Thk.
    Washer
    Material
    Each
    3 3/4"4 5/8"1/32"Steel5909K976000000
    3 3/4"4 5/8"1/16"Steel5909K98500000

    Oil-Embedded Thrust Bearings

    Image of Product. Front orientation. Thrust Bearings. Oil-Embedded Thrust Bearings.
    Our simplest-to-use thrust bearings, with no moving parts and no need to lubricate. Their porous surface releases oil over time, so you can install and forget them. While they run in most conditions, oil may drip away if temperatures climb too high. For extremely hot environments, consider graphite-lubricated bearings. All are fabricated, lubricated, and inspected in the U.S.
    841 Bearing Bronze—A balance of strength and speed makes these bearings a good choice for most applications. Also known as SAE 841 bearing bronze.
    Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away if the bearing heats up.
    For Shaft
    Dia.
    OD
    Thk.
    Dynamic Thrust Load
    Cap. @ Speed
    Base Oil
    Temp. Range,
    ° F
    Each
    841 Bearing Bronze
    3 3/4"5"1/8"10,500 lb. @ 30 rpmSynthetic Oil-35 to 3005906K625000000
     
    back to top