These steel ball bearings handle higher loads than stainless steel and plastic bearings.

Wider than our standard ball bearings, these rugged bearings are good for handling heavy loads at low speeds.

Bearings are 440C stainless steel for good corrosion resistance.

Good for applications with incidental food contact, these 440C stainless steel bearings have a food-grade, solid polymer lubricant between the balls and race that eliminates the need for additional lubrication.

Made of slippery plastic, these bearings do not require lubrication and have excellent corrosion and chemical resistance.

Made of PVDF, these bearings resist moisture absorption, so they won’t warp in underwater applications.

The flange ensures proper positioning inside a tube or housing.

Slip these bearings onto a shaft and secure with the included set screws, no special tools required.

Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components.

In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.

Also known as Oilite® bearings.

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

Unlike other sleeve bearings, these do not need to be fully inserted into a housing. Their unique shape creates a permanent, secure hold in thin panels.

A metal shell adds strength.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Made of FDA-listed materials or FDA compliant, these bearings are for use in food applications. They also withstand caustic and washdown environments.

Good for underwater applications, these bearings won’t swell or warp when wet.

Permanently and securely install these self-clinching bearings into panels, with no need for precision-bored holes or machined mounts.

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.

Also known as Oilite® bearings.

For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.

Embedded with lubricant that’s FDA compliant for incidental food contact, these bearings are good for high-load applications such as bottling and filling lines in food plants.

Use where high loads and speeds are not required.

A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.

Graphite provides a layer of dry lubrication that operates in high-temperature environments.

An aluminum shell adds strength.

These leaded bronze bearings are strong, wear resistant, and excellent at handling shock loads.

Also known as Oilite® bearings.

Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.

Made of 863 bearing bronze and embedded with NSF registered H1 oil, these bearings can tackle high-load applications in food plants, such as bottling and filling lines.

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.

These bearings stand up to a wider range of chemicals than other dry-running thrust bearings.

Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.

These bearings have higher radial load capacity, speed, and accuracy than standard needle-roller bearings.

The needles in these bearings roll freely in one direction, but lock to transmit torque when the rotation of the shaft is reversed. Also known as drawn-cup roller clutches.

Ball bearings operate with less friction than other bearings, so they can run at higher speeds.

A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication.

Also known as tapped-base bearings, these ball bearings mount to surfaces from the bottom through threaded holes. Because of their narrow profile, they’re commonly used in tight-clearance spaces, including systems where multiple shafts are mounted close together.

Use these bearings in corrosive environments and under water.

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings.

Made from slippery materials, these bearings reduce friction without the oily mess.

Capable of handling temperatures from -400° to 750° F, these graphalloy bearings withstand the widest temperature range of any of our mounted bearings.

Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface.

With a flexible layer of neoprene sandwiched between an oil-embedded bronze bearing and rigid steel shell, these bearings reduce wear and machinery noise.

Ball bearings operate with less friction than other bearings, so you can run them at higher speeds.

The lubricant in these mounted ball bearings is suitable for incidental contact with food.

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with two-bolt flange.

Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange.

Use these nylon or acetal bearings for light loads. The closed backing blocks out dust and other contaminants.

Handling speeds twice as fast as standard mounted sleeve bearings while limiting wear on your system, these bearings are made of PTFE-filled acetal.

Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface.

A bolt in each corner makes for a secure, even hold.

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with four-bolt flange.

Use these bearings in corrosive environments and under water.

Use ball bearings in debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Engineered for simultaneous linear and rotary motion, these bearings are used with round end-supported shafts.

Because they usually do not require lubrication, linear sleeve bearings outperform linear ball bearings in dirty environments.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

These fiberglass bearings are lightweight, nonmagnetic, and won’t conduct electricity.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard linear ball bearings for support rail shafts.

Sleeve bearings outperform ball bearings in dirty environments. Use them for low speed applications.

The flanged housing makes these bearings a good solution for vertical linear motion applications.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Choose ball bearings for debris-free environments and when speed is a necessity. They operate with less friction than sleeve bearings, so you can run them at higher speeds.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Mount these bearings on a support rail shaft for applications requiring maximum rigidity.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end.

The outer ring is built to handle higher speeds than standard shaft-mount track rollers.

Also known as yoke-style cam followers, these rollers have more mounting flexibility than threaded track rollers. They're typically mounted onto a shaft or clevis rod end.