System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter | Show |
|---|
|
For Shaft Diameter For Shaft Diameter | Hide |
|---|
Bearing Type Bearing Type |
|---|
 | Plain |
Minimum Temperature Minimum Temperature |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Lubrication Lubrication |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Color Color |
|---|
 | Off-White |
Thickness Thickness |
|---|
|
For Housing ID For Housing ID |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
Backing Material Backing Material |
|---|
|
About Plain Bearings
More
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Light Duty Dry-Running Sleeve Bearings
Use where high loads and speeds are not required.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Metric Nylon Bearings | ||||||
|---|---|---|---|---|---|---|
For 38mm Shaft Dia. | ||||||
| 48mm | 25mm | 310 lbs. @ 30 rpm | Off-White | -10° to 220° | 00000000 | 000000 |
High-Load Dry-Running Thrust Bearings
A steel backing adds strength to these slippery PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD, mm | Thick., mm | Dynamic Thrust Load Capacity | Temperature Range, °F | Each | |
Steel-Backed PTFE Plastic Bearings | |||||
|---|---|---|---|---|---|
For 38 mm Shaft Dia. | |||||
| 62 | 1.5 | 7,600 lbs. @ 30 rpm | -320° to 530° | 0000000 | 000000 |
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
SD Style Bushing | ||||||||
| 38mm | 54mm | 10mm | 3.3mm | 108 | Steel | Clamping Screws | 0000000 | 000000 |
SDS Style Bushing | ||||||||
| 38mm | 43mm | 10mm | 3.3mm | 108 | Steel | Clamping Screws | 0000000 | 00000 |
SK Style Bushing | ||||||||
| 38mm | 59mm | 10mm | 3.3mm | 180 | Steel | Clamping Screws | 0000000 | 00000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
1610 Style Bushing | |||||||||
| 38mm | 25mm | 10mm | 3.3mm | 8° | 175 | Steel | Set Screws | 000000000 | 000000 |
1615 Style Bushing | |||||||||
| 38mm | 38mm | 10mm | 3.3mm | 8° | 175 | Steel | Set Screws | 000000000 | 00000 |
2012 Style Bushing | |||||||||
| 38mm | 32mm | 10mm | 3.3mm | 8° | 280 | Steel | Set Screws | 000000000 | 00000 |
2517 Style Bushing | |||||||||
| 38mm | 44mm | 10mm | 3.3mm | 8° | 430 | Steel | Set Screws | 000000000 | 00000 |
Split-Tapered Bushings
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
Bushings with a machine key fit into a matching keyway on a sprocket or pulley for high-torque applications.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | Overall Wd. | Taper | Fastener Tightening Torque, in.-lbs. | Each | |
Steel | |||||
|---|---|---|---|---|---|
H Style Bushing with Machine Key | |||||
| 38mm | 1 1/4" | 3° | 95 | 00000000 | 000000 |