System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
For Load Direction For Load Direction |
|---|
 | Thrust |
ID ID | Show |
|---|
|
ID ID | Hide |
|---|
Ball Material Ball Material |
|---|
|
Maximum Speed Maximum Speed |
|---|
|
Washer Material Washer Material |
|---|
|
Ball Bearing Type Ball Bearing Type |
|---|
 | Standard |
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
Bearing Type Bearing Type |
|---|
 | Ball |
Thickness Thickness |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Minimum Temperature Minimum Temperature |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Cage Material Cage Material |
|---|
|
Lubrication Lubrication |
|---|
|
Seal Type Seal Type |
|---|
|
About Ball and Roller Bearings
More
Thrust Ball Bearings
Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 1/8" | 7/16" | 0.193" | Nylon Plastic | Steel | 15 | 120 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 00000 |
Corrosion-Resistant Thrust Ball Bearings
A combination of stainless steel and nylon components provide increased corrosion resistance over standard thrust ball bearings. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 1/8" | 7/16" | 0.193" | Nylon Plastic | 410 Stainless Steel | 10 | 80 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 00000 |
Press-Fit Drill Bushings
Mount flush with jig plates for precise drilling. These bushings can also be used as spacers, shims, and machinery bushings.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.128" ID | ||||||||||||
| 1/4" | 1/4" | 3.25 mm | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1/4" | 1/2" | 3.25 mm | 0.0001" to 0.0004" | 0.0013" to 0.0016" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 0000000 | 0000 | 0000 | 0000 |