About Plain Bearings
More
High-Load Food Industry Oil-Embedded Thrust Bearings
Made of 863 iron-copper and embedded with NSF registered H1 oil, these bearings can tackle high-load applications in food plants, such as bottling and filling lines. Startup friction causes these bearings to release a thin layer of oil onto their surface. The oil is safe for incidental contact with food. Also known as Super Oilite® bearings, these bearings have high iron content, so they’re strong and hold up to shock loads.
| OD | Thickness | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Iron-Copper Bearings | |||||||
|---|---|---|---|---|---|---|---|
For 3/8" Shaft Dia. | |||||||
| 3/4" | 1/16" | 490 lbs. @ 120 rpm | Lubricated | SAE 20 Oil | -75° to 300° | 0000000 | 00000 |
Press-Fit Drill Bushings
Also known as jig bushings, these drill bushings fit inside fixture plate holes to precisely guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings.
Press into place with a manual or hydraulic press. Since these bushings are sized slightly larger than the hole for an extremely tight fit, they’ll stay put permanently. These are ANSI Type P bushings—also known as headless bushings—which means you don’t need to counterbore the hole to mount them flush.
Don't see the size you need? Additional sizes are available.
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.386" ID | ||||||||||||
| 5/8" | 5/16" | W | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 5/8" | 3/8" | W | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 0000 | 0000 | 0000 |
| 5/8" | 1/2" | W | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 0000 | 0000 | 0000 |
| 5/8" | 5/8" | W | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 0000 | 0000 | 0000 |
| 5/8" | 3/4" | W | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 0000 | 0000 | 0000 |
| 5/8" | 1" | W | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 5/8" | 1 1/4" | W | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 5/8" | 1 3/4" | W | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 0000 |
| 3/4" | 5/8" | W | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 0000 | 0000 | 0000 |
| 3/4" | 3/4" | W | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 0000 | 0000 | 0000 |
| 3/4" | 1" | W | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 3/4" | 1 1/4" | W | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 0000 | 0000 |
| 3/4" | 2 1/2" | W | 0.0001" to 0.0005" | 0.0015" to 0.0018" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
Press-Fit Drill Bushings with Head
A flanged head on these bushings acts as a stop, so they won’t press through your jig even under extreme drilling pressure. They’re ANSI Type H bushings, also known as headed bushings. The head adds support and protects the jig from damage caused by heavy use, so they’re often used in jigs made of thin or soft materials. These bushings guide your drill bit, reamer, or other cutting bit to create accurate, consistent holes from one workpiece to the next. They’re also used as spacers, shims, and machinery bushings. Made of hardened, ground steel, they hold their shape and resist wear, so they last for many cycles without needing to be replaced.
To install, fit the bushing into a hole in your jig. In a standard hole, the head will sit above the jig plate; to mount flush, install in a countersunk hole. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once it’s centered, press the bushing into place with a hydraulic or lever press.
Don't see the size you need? Additional sizes are available.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.386" ID | ||||||||||||||
| 5/8" | 3/4" | W | 51/64" | 7/32" | 0.0001" to 0.0005" | 0.0014" to 0.0017" | -0.01" to 0.01" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Removable Drill Bushings
Replace worn bushings and quickly change IDs without needing to repeatedly use a lever press. Instead of pressing bushings in and out of your jig fixture, which can cause damage, these bushings slide in and out of sleeves (sold separately). By swapping in a bushing with a different ID, you can change the size of your bit and still use the same hole in your fixture. All are made to tight dimensional tolerances for consistent, accurate results, even as you change them in and out. They're also known as slip-fixed and renewable bushings.
Choose a sleeve with a length that matches the length of your bushing. To prevent bushings from spinning inside the sleeve as you drill, pair a standard sleeve with a lock screw, or use a locking sleeve. For faster placement in and removal from sleeves, use a handle.
Lock screws thread into a hole in your jig. The head of the screw fits into a notch on the bushing's head, which keeps the bushing from spinning.
Locking sleeves act as a sleeve and lock screw at the same time. They have a raised flange that fits into the notch on the bushing's head, keeping the bushing in place. Knurled sleeves grip the sides of a hole to prevent rotation. Press or mold them into plastic tooling. Smooth sleeves are slightly oversized for a snug fit. They’re usually installed in metal tooling—press them into place with a manual or hydraulic press.
Head | Tolerance | Each | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | Lock Screw/Bushing Ctr.-to-Ctr. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.386" ID | |||||||||||||||
| 3/4" | 1" | W | 1 3/64" | 1/4" | 3/4" | 0.0001" to 0.0005" | -0.0002" to 0" | -0.01" to 0.01" | SF | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 00000 |
| For Bushing OD | ID | OD | Lg. | ID Tolerance | For Drill Bushing Type | Material | Hardness | Sleeve ANSI Number | Each | |
| 3/4" | 3/4" | 1" | 3/8" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | L-64-6 | 00000000 | 000000 |
| 3/4" | 3/4" | 1" | 1/2" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | L-64-8 | 00000000 | 00000 |
| 3/4" | 3/4" | 1" | 3/4" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | L-64-12 | 00000000 | 00000 |
| 3/4" | 3/4" | 1" | 1" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | L-64-16 | 00000000 | 00000 |
| 3/4" | 3/4" | 1" | 1 3/8" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | L-64-22 | 00000000 | 00000 |
| 3/4" | 3/4" | 1" | 1 3/4" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | L-64-28 | 00000000 | 00000 |
|  Knurled |  Smooth | ||
 | ||||
| For Bushing OD | ID | OD | Lg. | Head Dia. | Flange Distance | ID Tolerance | For Drill Bushing Type | Material | Hardness | Each | |
Knurled | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 3/4" | 3/4" | 1" | 3/4" | 1 1/16" | 21/32" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | 000000000 | 000000 |
| 3/4" | 3/4" | 1" | 1" | 1 1/16" | 21/32" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | 000000000 | 00000 |
| 3/4" | 3/4" | 1" | 1 1/4" | 1 1/16" | 21/32" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | 000000000 | 00000 |
Smooth | |||||||||||
| 3/4" | 3/4" | 1" | 3/4" | 1 1/16" | 21/32" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | 000000000 | 00000 |
| 3/4" | 3/4" | 1" | 1" | 1 1/16" | 21/32" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | 000000000 | 00000 |
| 3/4" | 3/4" | 1" | 1 1/4" | 1 1/16" | 21/32" | 0.0003" to 0.0006" | SF | Steel | Rockwell C61 | 000000000 | 00000 |
Drill Bushings for Plastic
Serrations line the sides of these bushings to keep them from spinning while you drill. Also known as jig bushings, they’re pressed or molded into plastic tooling to guide drill bits, counterbores, and reamers. They help you create consistent, accurate holes from part to part.
Also Available: Other sizes. Please select 3378A999 and specify ID, OD, and length.
Tolerance | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Drill Bushing Type | Material | Hardness | Each | |
0.386" ID | |||||||||
| 5/8" | 1/2" | W | 0.0001" to 0.0005" | 0.01" to 0.025" | SG | Alloy Tool Steel | Rockwell C61 | 00000000 | 00000 |
Secure-Hold Drill Bushings for Plastic
Designed to grip slippery plastic, the knurls on these bushings keep them from spinning while you drill. Their hold is stronger than serrated bushings, so they can withstand more force. Press or mold into plastic tooling to guide your drill bit and create accurate, consistent holes.
Also Available: Other sizes. Please select 3379A999 and specify ID, OD, and length.
Tolerance | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Drill Bushing Type | Material | Hardness | Each | |
0.386" ID | |||||||||
| 5/8" | 1/2" | W | 0.0001" to 0.0005" | 0.01" to 0.025" | DG | Alloy Tool Steel | Rockwell C61 | 00000000 | 00000 |
Drill Bushings for Soft Metal and Wood
Serrations on these bushings dig into wood, aluminum, and other soft metals to keep them from spinning while you drill. Also known as jig bushings, they fit inside fixture plates to guide drill bits, counterbores, and reamers. They improve accuracy so that your drilled holes and cuts are consistent from part to part.
Also Available: Other sizes. Please select 3377A999 and specify ID, OD, and length.
Tolerance | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Drill Bushing Type | Material | Hardness | Each | |
0.386" ID | |||||||||
| 3/4" | 1/2" | W | 0.0001" to 0.0005" | -0.0002" to 0" | SP | 1144 Carbon Steel | Rockwell C61 | 00000000 | 000000 |
Removable Drill Bushings for Thin Metal
Unlike most bushings, these won’t buckle the material or distort the hole when installed in thin-gauge aluminum and steel fixture plates. They’re held in place by a lock ring (sold separately), so they’re easy to remove and reuse. Also known as jig bushings, they accurately guide drill bits, counterbores, reamers, and other cutting tools. Use them to make sure your drilled holes and cuts are consistent from part to part.
Tolerance | Thread | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ID | OD | Lg. | For Drill Bit Size | ID | OD | For Material Thick. | Size | Lg. | Direction | Material | Hardness | Each | |
| 0.386" | 3/4" | 1/2" | W | 0.0001" to 0.0015" | 0.003" to 0.005" | 1/64"-3/8" | 3/4"-16 | 1/4" | Left Hand | 1144 Carbon Steel | Rockwell C59 | 00000000 | 000000 |
| For Bushing OD | For Material Thick. | OD | Lg. | Material | Each | |
| 3/4" | 1/64"-1/8" | 7/8" | 3/8" | Aluminum | 00000000 | 000000 |
| 3/4" | 1/64"-1/8" | 1" | 3/8" | Aluminum | 00000000 | 0000 |
| 3/4" | 9/64"-3/16" | 7/8" | 5/16" | Aluminum | 00000000 | 00000 |
| 3/4" | 9/64"-3/16" | 1" | 5/16" | Aluminum | 00000000 | 0000 |
| 3/4" | 13/64"-3/8" | 7/8" | 3/16" | Aluminum | 00000000 | 00000 |
| 3/4" | 13/64"-3/8" | 1" | 3/16" | Aluminum | 00000000 | 0000 |