System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
For Housing ID For Housing ID |
|---|
|
ID ID | Show |
|---|
|
ID ID | Hide |
|---|
For Load Direction For Load Direction |
|---|
 | Combined Radial and Thrust |
 | Thrust |
Ball Material Ball Material |
|---|
|
Washer Material Washer Material |
|---|
|
Cage Material Cage Material |
|---|
|
Dynamic Thrust Load Capacity Dynamic ThrustLoad Capacity |
|---|
|
For Shaft Type For Shaft Type |
|---|
 | Round |
Ball Bearing Type Ball Bearing Type |
|---|
 | Standard |
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Lubrication Lubrication |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Maximum Speed Maximum Speed |
|---|
|
Seal Type Seal Type |
|---|
|
About Plain Bearings
More
About Ball and Roller Bearings
More
Thrust Ball Bearings
Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 1/2" | 15/16" | 0.249" | Nylon Plastic | Steel | 30 | 200 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 00000 |
Corrosion-Resistant Thrust Ball Bearings
A combination of stainless steel and nylon components provide increased corrosion resistance over standard thrust ball bearings. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 1/2" | 15/16" | 0.249" | Nylon Plastic | 410 Stainless Steel | 20 | 140 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 00000 |
High-Load Oil-Embedded Flanged Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
863 Bearing Bronze Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 1/2" Shaft Dia. | ||||||||||
| 3/4" | 5/8" | 1" | 1/8" | 690 lbs. @ 120 rpm | 650 lbs. @ 120 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 00000000 | 00000 |
| 3/4" | 1 1/4" | 1" | 1/8" | 1,350 lbs. @ 120 rpm | 650 lbs. @ 120 rpm | Lubricated | ISO 460 Oil | -15° to 300° | 0000000 | 0000 |
Chemical-Resistant Dry-Running Thrust Bearings
These bearings stand up to a wider range of chemicals than other dry-running thrust bearings. They are lightweight and strong.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
PEEK Plastic Bearings | ||||||
|---|---|---|---|---|---|---|
For 1/2" Shaft Dia. | ||||||
| 1" | 1/16" | 460 lbs. @ 120 rpm | Black | -40° to 500° | 000000 | 00000 |
Shims for Ball Bearings
For technical drawings and 3-D models, click on a part number.
Adjust spacing between bearings and other components on shafts. These shims are sized to fit the outer rim of a bearing.
316 stainless steel shims have the best corrosion resistance of our stainless steel shims.
18-8 stainless steel shims offer good corrosion resistance.
Brass shims are corrosion resistant and nonmagnetic.
For Bearing | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| ID | OD | ID | ID Tolerance | OD | OD Tolerance | Min. Hardness | Magnetic Properties | Choose a Thick. | Pkg. Qty. | Pkg. | |
316 Stainless Steel | |||||||||||
| 1/4" | 5/8" | 0.503" | 0" to 0.005" | 0.623" | -0.005" to 0" | Rockwell B90 | May Be Mildly Magnetic | 10 | 000000000 | 000000 | |
18-8 Stainless Steel | |||||||||||
| 1/4" | 5/8" | 0.503" | 0" to 0.005" | 0.623" | -0.005" to 0" | Rockwell B70 | May Be Mildly Magnetic | 25 | 000000000 | 00000 | |
260 Brass | |||||||||||
| 1/4" | 5/8" | 0.503" | 0" to 0.005" | 0.623" | -0.005" to 0" | Rockwell B70 | Nonmagnetic | 10 | 000000000 | 0000 | |