System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
Bearing Type Bearing Type |
|---|
 | Plain |
For Housing ID For Housing ID |
|---|
|
ID ID | Show |
|---|
|
ID ID | Hide |
|---|
Lubrication Lubrication |
|---|
|
For Load Direction For Load Direction |
|---|
 |  |
| Radial | Combined Radial and Thrust |
 | |
| Thrust |
For Shaft Type For Shaft Type |
|---|
 | Round |
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
Lubrication Method Lubrication Method |
|---|
|
Dynamic Thrust Load Capacity Dynamic ThrustLoad Capacity |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement) |
|---|
Lubricant Lubricant |
|---|
|
Seal Type Seal Type |
|---|
|
Shaft Mount Type Shaft Mount Type |
|---|
| Slip Fit |
Dynamic Radial Load Capacity Dynamic RadialLoad Capacity |
|---|
|
About Plain Bearings
More
About Washers
More
Multipurpose Dry-Running Sleeve Bearings
Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings. Bearings resist corrosion in outdoor and saltwater environments.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
For 1/2" Shaft Dia. | ||||||
|---|---|---|---|---|---|---|
| 3/4" | 1/2" | 390 lbs. @ 120 rpm | Blue | -40° to 150° | 0000000 | 000000 |
Multipurpose Dry-Running Flanged Sleeve Bearings
Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings. Bearings resist corrosion in outdoor and saltwater environments.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Polyester Fabric-Reinforced PTFE Plastic Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 1/2" Shaft Dia. | |||||||||
| 3/4" | 1/2" | 1" | 1/8" | 390 lbs. @ 120 rpm | 460 lbs. @ 120 rpm | Blue | -40° to 150° | 0000000 | 000000 |
| 3/4" | 3/4" | 1" | 1/8" | 590 lbs. @ 120 rpm | 460 lbs. @ 120 rpm | Blue | -40° to 150° | 0000000 | 00000 |
| 3/4" | 1" | 1" | 1/8" | 790 lbs. @ 120 rpm | 460 lbs. @ 120 rpm | Blue | -40° to 150° | 0000000 | 00000 |
Oil-Embedded Thrust Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 1/2" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1" | 1/16" | 930 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 1" | 3/32" | 930 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
| 1" | 1/8" | 930 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 0000 |
High-Load Oil-Embedded Thrust Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 1/2" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1" | 3/32" | 650 lbs. @ 120 rpm | Lubricated | SAE 90 Oil | -15° to 300° | 0000000 | 00000 |
Food Industry Oil-Embedded Thrust Bearings
The oil in these bearings is suitable for incidental contact with food. Startup friction causes them to release a thin layer of oil on the bearing’s surface.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 1/2" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1" | 1/16" | 930 lbs. @ 120 rpm | Lubricated | SAE 20 Oil | -75° to 300° | 000000 | 00000 |
Electrical-Insulating Sleeve Washers
Also known as shoulder or insulator washers, these nonmetal washers block electrical current and prevent galvanic corrosion from mating different types of metal.
Nylon 6/6 washers have good abrasion resistance. Exposure to moisture may cause them to expand.
For technical drawings and 3-D models, click on a part number.
Temperature Range, °F | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Screw Size | ID | OD | Sleeve OD | Thick. | Overall Ht. | Min. | Max. | Hardness | Color | Pkg. Qty. | Pkg. | |
Nylon 6/6 Plastic | ||||||||||||
| 1/2" | 0.505" | 0.750" | 0.625" | 0.062" | 0.374" | -40° | 180° | Rockwell R108 | Off-White | 50 | 000000000 | 00000 |