System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
ID ID | Show |
|---|
|
ID ID | Hide |
|---|
Cage Material Cage Material |
|---|
|
Ball Material Ball Material |
|---|
|
Thickness Thickness |
|---|
|
Ball Bearing Type Ball Bearing Type |
|---|
 | Standard |
For Shaft Type For Shaft Type |
|---|
 | Round |
Maximum Speed Maximum Speed |
|---|
|
Washer Material Washer Material |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
Static Thrust Load Capacity Static Thrust Load Capacity |
|---|
|
Maximum Temperature Maximum Temperature |
|---|
|
Minimum Temperature Minimum Temperature |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
Lubrication Lubrication |
|---|
|
Seal Type Seal Type |
|---|
|
Plain Bearing Type Plain Bearing Type |
|---|
 | Sleeve |
About Plain Bearings
More
About Ball and Roller Bearings
More
Thrust Ball Bearings
Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 5/8" | 1 1/8" | 0.342" | Nylon Plastic | Steel | 35 | 250 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 00000 |
Corrosion-Resistant Thrust Ball Bearings
A combination of stainless steel and nylon components provide increased corrosion resistance over standard thrust ball bearings. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
| 5/8" | 1 1/8" | 0.342" | Nylon Plastic | 410 Stainless Steel | 25 | 170 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 00000 |
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 5/8" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 15/16" | 3/4" | 940 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | 10° to 175° | 00000000 | 00000 |