System of Measurement System of Measurement |
|---|
|
For Shaft Diameter For Shaft Diameter |
|---|
|
Mounted Bearing Type Mounted Bearing Type |
|---|
 |  |
| Base Mount | Four-Bolt Flange Mount |
Shaft Mount Type Shaft Mount Type |
|---|
|
Housing Material Housing Material |
|---|
|
Bearing Type Bearing Type |
|---|
 | Ball |
Alignment Style Alignment Style |
|---|
|
Seal Type Seal Type |
|---|
|
ID ID | Show |
|---|
|
ID ID | Hide |
|---|
Lubricant Lubricant |
|---|
|
For Load Direction For Load Direction |
|---|
 | Radial |
Static Radial Load Capacity Static Radial Load Capacity |
|---|
|
Dynamic Radial Load Capacity Dynamic Radial Load Capacity |
|---|
|
Grease Fitting Included Grease Fitting Included |
|---|
|
Mounting Hole Diameter Mounting Hole Diameter |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
About Ball and Roller Bearings
More
Mounted Ball Bearings
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 1 3/8" | 1 7/8" | 4 1/8" | 6 9/16" | 1 7/8" | 13/16" | 1/2" | 5" | 5,750 | 3,450 | 4,600 | -20° to 220° | Self Aligning | Lubricated | 0000000 | 0000000 |
Mounted Ball Bearings with Four-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
| 1 3/8" | 4 5/8" | 4 5/8" | 1 29/32" | 1/2" | 9/16" | 3 5/8" | 5,700 | 3,400 | 5,300 | -20° to 210° | Self Aligning | Lubricated | 00000000 | 0000000 |
Insert Bearings
Swap out worn inserts instead of replacing the entire mounted unit. Use the manufacturer model number on your existing mounted bearing to choose a compatible insert. Inserts must be used with the manufacturer model number specified.
For technical drawings and 3-D models, click on a part number.
| For Shaft Dia. | For Mounted Bearing Model No. | Each | |
SKF Steel Insert Bearings | |||
|---|---|---|---|
Shaft Mount Type: Set Screw | |||
| 1 3/8" | F4B 106-TF, FY 1.3/8 TF, FYT 1.3/8 TF | 0000000 | 000000 |