Thermoplastic-blend bearings have low moisture absorption and create very low friction in applications with light loads, and frequent starts and stops.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Thermoplastic-Blend Bearings
For Housing ID	Lg.	Flange OD	Flange Thick.	Dynamic Radial Load Capacity	Dynamic Thrust Load Capacity	Color	Temperature Range, °F		Each
For 11mm Shaft Dia.
13mm	5mm	18mm	1mm	60 lbs. @ 120 rpm	105 lbs. @ 120 rpm	Yellow	-50° to 190°	00000000	00000

Light Duty Dry-Running Thrust Bearings

Use where high loads and speeds are not required.

Thermoplastic bearings are fiber reinforced and lubricant infused for good wear resistance and low friction with light and medium loads.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Thermoplastic Blend Bearings
OD	Thick.	Dynamic Thrust Load Capacity	Color	Temperature Range, °F		Each
For 11 mm Shaft Dia.
15mm	1mm	15 lbs. @ 120 rpm	Gray	-40° to 260°	0000000	00000
27mm	0.5mm	85 lbs. @ 120 rpm	Gray	-40° to 260°	0000000	0000

Ready-Mount Bearing Housings

Mount bearings quickly by using these precision housings, which don’t require any machining. They support a shaft that’s perpendicular or parallel to their mounting surface and let you replace the bearings as needed. Made of aluminum, they’re lightweight, durable, and have good corrosion resistance.

For technical drawings and 3-D models, click on a part number.

		Overall			Mounting
For Bearing OD	Center Height	Height	Length	Width	Hole Diameter	Center-to-Center		Each
2014 Aluminum Housing
For 5mm Bearing Width
11mm	9.5mm	19mm	37mm	5mm	1/8"	29mm	0000000	000000
For 10mm Bearing Width
11mm	9.5mm	19mm	37mm	10mm	13/64"	29mm	0000000	00000
11mm	14.3mm	29mm	57mm	10mm	9/32"	44mm	0000000	00000
For 11mm Bearing Width
11mm	14.3mm	29mm	57mm	11mm	9/32"	44mm	0000000	00000
For 16mm Bearing Width
11mm	14.3mm	29mm	57mm	16mm	9/32"	44mm	0000000	00000

Ready-Mount Bearing Housings with Two-Bolt Flange

Quickly mount bearings in these precision-flanged housings, no machining required. They support a shaft that’s perpendicular or parallel to their mounting surface and let you replace the bearings as needed. Housings are made of aluminum so they’re lightweight and durable with good corrosion resistance.

For technical drawings and 3-D models, click on a part number.

	Overall				Mounting
For Bearing OD	Height	Length	Width	Flange Thickness	Hole Diameter	Hole Center-to-Center		Each
2014 Aluminum
For 7mm Bearing Width
11mm	7mm	41mm	19mm	4.5mm	11/64"	32mm	00000000	000000
For 10mm Bearing Width
11mm	9mm	41mm	19mm	4.5mm	11/64"	32mm	00000000	00000
For 11mm Bearing Width
11mm	11mm	57mm	28mm	4.5mm	9/32"	44mm	00000000	00000
For 16mm Bearing Width
11mm	15mm	57mm	28mm	4.5mm	9/32"	44mm	00000000	00000

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. Some bushings have internal chamfers on both ends, so no matter which end of the bushing is inserted into your jig, your bits, pins, and other tooling enter easily. Having an internal chamfer on the bottom of your bushing may cause shavings to get caught and bind as you remove the bit, however.

DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.

Don't see the size you need? Additional sizes are available.

For technical drawings and 3-D models, click on a part number.

				Tolerance								Each
OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
11 mm ID
18	12	Both Ends	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	000000	00000	00000
18	12	One End	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	00000	0000	0000
18	20	Both Ends	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	00000	00000	00000
18	20	One End	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	00000	00000	0000
18	25	Both Ends	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	00000	00000	00000
18	25	One End	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	00000	00000	00000

Metric Press-Fit Drill Bushings with Head

Shown in Countersunk Hole

Shown in Standard Hole

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.

Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.

These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.

For technical drawings and 3-D models, click on a part number.

		Head		Tolerance								Each
OD, mm	Lg., mm	OD, mm	Thick., mm	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
11 mm ID
18	8	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	000000	000000	000000
18	16	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
18	21	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000

21 Products

About Plain Bearings

Light Duty Dry-Running Flanged Sleeve Bearings

Light Duty Dry-Running Thrust Bearings

Ready-Mount Bearing Housings

Ready-Mount Bearing Housings with Two-Bolt Flange

Metric Press-Fit Drill Bushings

Metric Press-Fit Drill Bushings with Head