14.2 mm ID Bearings | McMaster-Carr

	REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration, Evaluation, Authorization and Restriction of Chemicals)

REACH Compliant

	Color Color

	White

	Bearing Type Bearing Type

	Plain

	Drill Bushing Style Drill Bushing Style

Smooth

	Drill Bushing Type Drill Bushing Type

	For Drill Bit Size For Drill Bit Size

14.2 mm

	Hardness Hardness

Rockwell C61

View catalog pages (3)

Forward

How can we improve?

5 Products

About Plain Bearings

Use these bearings in applications with frequent starts and stops because they operate with very little friction.

PTFE bearings have good chemical resistance.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

PTFE Plastic Bearings
OD	Thick.	Dynamic Thrust Load Capacity	Color	Temperature Range, °F		Each
For 14mm Shaft Dia.
27.7mm	2mm	12 lbs. @ 60 rpm	White	-450° to 500°	0000000	000000

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.

Don't see the size you need? Additional sizes are available.

For technical drawings and 3-D models, click on a part number.

				Tolerance								Each
OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
14.2 mm ID
22	16	One End	14.2 mm	0.016 to 0.034	0.015 to 0.028	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	000000	000000	00000

Metric Press-Fit Drill Bushings with Head

Shown in Countersunk Hole

Shown in Standard Hole

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.

Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.

These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.

For technical drawings and 3-D models, click on a part number.

		Head		Tolerance								Each
OD, mm	Lg., mm	OD, mm	Thick., mm	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
14.2 mm ID
22	12	26	4	0.016 to 0.034	0.015 to 0.028	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	000000	000000	000000
22	24	26	4	0.016 to 0.034	0.015 to 0.028	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
22	32	26	4	0.016 to 0.034	0.015 to 0.028	-0.3 to 0.3	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000

About Plain Bearings

Ultra-Low-Friction Dry-Running Thrust Bearings

Metric Press-Fit Drill Bushings

Metric Press-Fit Drill Bushings with Head